Shivam Engineering Works Muzaffarnagar, Uttar Pradesh

Vibration Machine\\nAIM 418-2 & AIM 418-3\\nRef. Standard: IS:4031, IS:10080, EN 196-1:413-2, EN 13454-2\\nA specially designed Vibration Machine is used for vibrating the mix in moulds at a frequency of 12,000 ± 400 cycles per minute, as per specifications.\\nThe Vibrator is mounted over coiled springs and the vibrations are developed by means of a revolving eccentric shaft. The centre of gravity of the vibrator, including the cube and mould, is either at the centre of the eccentric shaft or within 25 mm below it. The simple design of the machine facilitates easy assembly and dismantling of the cube moulds. Each machine is supplied with AIM 414 one cube mould with ISI Certification Mark and poking rod.\\nSuitable for operation on 220V, 50Hz, Single Phase, AC supply.\\n \\nThe equipment consists of the following replaceable parts:\\n\\n\\nAIM 414 – Mould Steel, for 70.6 mm Cube with ISI Certification Mark as per IS:10080\\n\\n\\nAIM 41801 – Side Spring\\n\\n\\nAIM 41802 – Supporting Springs (Set of four)\\n\\n\\nAIM 41803 – Springs for Fitting Mould (Set of two)\\n\\n\\nAIM 41804 – Endless Belt\\n\\n\\nAIM 41805 – Belt Guard\\n\\n\\nAIM 41807 – Eccentric Shafts with bearing\\n\\n\\n \\nOrdering Information:\\n\\n\\nAIM 418-2 – Vibration Machine with built-in Digital Timer, NABL Calibrated\\n\\n\\nAIM 418-3 – Vibration Machine with built-in Digital Timer, without Calibration\\n\\n\\n \\nOptional Accessories:\\n\\n\\nAIM 41855-S1 – Top attachment of vibration machine suitable for 50 mm mould\\n\\n\\nNote: CE mark available on request

Type : Vibration Machine

Application : Vibrating The Mix In Moulds At A Frequency Of 12,000 ± 400 Cycles Per Minute.

Vibratory Compaction\\nVibrating Table\\nModels: AIM 364, AIM 365-1, AIM 366-1 & AIM 367-1\\nRef.: EN 12350-6, 7, 12390-2, 13286-50\\nProper compaction of cement concrete while casting specimens for compression testing is essential to achieve higher compressive strength.\\nAIMIL Vibrating Table is ideally suited for this purpose.\\n\\n\\nThe table top is suitable to hold cube moulds and has stops along its edges to prevent moulds from sliding off the table during operation.\\n\\n\\nThe specially designed vibro motor operates the vibrator.\\n\\n\\nPower Supply: Suitable for operation on 220 V, 50 Hz, Single Phase, AC supply.\\n \\n 

Type : Vibrating Table

Usage/Application : Proper Compaction Of Cement Concrete While Casting Specimens For Compression Testing

Universal Testing Machine\\nAIM 651, AIM 652 & AIM 653\\nSalient Features:\\n \\n\\n\\nLoading accuracy as high as ±1% of the indicating value\\n\\n\\nStrain measurement at variable speed to cover a wide range of materials adjustable by the manual control valve.\\n\\n\\nHigh reading accuracy and rugged design of digital display.\\n\\n\\nSimple control to facilitate ease of operation.\\n\\n\\nFully enclosed and protected load measuring system.\\n\\n\\nRobust load frame with extremely rigid construction.\\n\\n\\nLarge effective clearance between columns enables testing of standard specimens as well as structures.\\n\\n\\nMotor driven threaded columns for UP/DOWN movement of lower crosshead for quick change over of specimen, grips and attachment.\\n\\n\\nWide range of standard and special accessories including load stabilizer (Optional).\\n\\n

Type : Universal Testing Machine

Color : Blue

Condition : New

Application : Testing

Certification : Iso 9001:2008

Country of Origin : India

Loading Accuracy : +/-1% Of The Indicating Value

Design : Rugged

Control : Simple

Universal Automatic Compactor\\\\nModels: AIM 114-1, AIM 114-1BS, AIM 114-1ASTM\\\\n \\\\nPurpose:\\\\nThis mechanical compactor is designed for soil compaction and penetration testing (e.g., CBR test preparation). It ensures uniform and consistent compaction, reducing human effort and error compared to manual methods.\\\\n \\\\nKey Features:\\\\n\\\\n\\\\nComplies with IS:2720 (Part 7 & 8) and ASTM standards.\\\\n\\\\n\\\\nElectrically operated mechanical compactor, suitable for heavy and light compaction.\\\\n\\\\n\\\\nIdeal for laboratories conducting CBR, Proctor, or other compaction-based soil strength tests.\\\\n\\\\n\\\\nMould and rammer mounted on base; rammer travels vertically to compact soil inside mould.\\\\n\\\\n\\\\nRammer Circular Faces:\\\\n\\\\n\\\\nWeight: Adjustable to 2.6 kg or 4.9 kg\\\\n\\\\n\\\\nDrop Height: Adjustable to 310 mm or 450 mm\\\\n\\\\n\\\\n\\\\n\\\\nSuitable for:\\\\n\\\\n\\\\n100 mm and 150 mm diameter moulds\\\\n\\\\n\\\\n\\\\n\\\\nHeavy-duty construction ensures stable and accurate operation\\\\n\\\\n\\\\nPower Supply: 220V, 50 Hz, Single Phase (AC)\\\\n\\\\n\\\\n 

Automation Grade : Automatic

Application : Industrial Use,Soil Compaction And Penetration Testing

Country of Origin : India

Type : Automatic Compactor

Tile Flexure Strength Testing Machine\\nAIM 460\\nRef. Standard – IS:654, 1237 For clay roofing tiles (Mangalore Pattern) and Cement Concrete Flooring Tiles. This is a double lever (leverage 1:12) loading machine and the load is applied by flow of lead shots which automatically stops when the sample breaks. The load is applied at the rate of 450 to 550 N/minute or 200 kg/minute as per relevant standards test requirement. The accuracy of load indication is within ±2%. The sample is mounted between rollers 40mm dia or 12mm dia as per relevant standards.\\nCapacity: 200 kg\\n \\nOrdering Information:\\n\\n\\nAIM 460 – Tile Flexure Strength Testing Machine\\n\\n\\n \\n \\nIf you’d like, I can help create a comparison sheet between machines, prepare a quotation format, or provide test procedures as per the standards mentioned (IS:10070, IS:654, IS:1237). Let me know!

Production Capacity : 200 Kg

Standard Tar Viscometer\\nAIM 531 & 533\\nRef. Standards – IS:1206, IP 72, STPTC. RT2, RT3, BS:2000, (Part 72)\\nFor determining the viscosity of cut back bitumen and road oil. The viscometer consists of a chrome plated copper bath, with a drain valve and a central tube to receive the test cup and to position the stirrer, and is mounted on a stand with levelling feet. Stirrer has a curved shield and is provided with an insulated handle, thermometer socket and swivel support for the valve.

Type : Viscometer

Material : Chrome Plated Copper Bath

Application : Determining Viscosity Of Cut Back Bitumen And Road Oil

Feature : Drain Valve, Central Tube, Stirrer With Curved Shield, Insulated Handle, Thermometer Socket, Swivel Support For Valve

Color : Chrome Plated

Slump Test Apparatus\\nModel: AIM 334 Reference Standards:\\n\\n\\nIS: 7320\\n\\n\\nBS: 1881\\n\\n\\nASTM C 143\\n\\n\\nAASHTO T119\\n\\n\\nDescription:\\n\\n\\nThe slump cone dimensions:\\n\\n\\nTop ID: 100 mm\\n\\n\\nBottom ID: 200 mm\\n\\n\\nHeight: 300 mm\\n\\n\\n\\n\\nProcedure:\\n\\n\\nThe cone is filled with freshly mixed concrete in four layers, each tamped.\\n\\n\\nThe top is leveled off, and the cone is lifted vertically.\\n\\n\\nThe slump (vertical subsidence of concrete) is immediately measured.\\n\\n\\n\\n\\n  Design Features:\\n\\n\\nBase has cleats for better ground grip.\\n\\n\\nPositive clamping of the cone to the base.\\n\\n\\nSwivel handle also acts as a datum, avoiding the use of a separate rule/bar for measurement.\\n\\n\\n\\n \\nTypes of Slump (Diagram):\\n\\n\\n\\n(A) True Slump\\n\\n\\n(B) Shear Slump\\n\\n\\n(C) Collapse Slump\\n\\n\\nReplaceable Parts:\\n\\n\\nAIM 33401: Slump Cone – 1 No.\\n\\n\\nAIM 33402: Base Plate with Swivel Handle – 1 No.\\n\\n\\nAIM 345: Tamping Rod, Steel, 16 mm dia × 600 mm, ISI Certified – 1 No.\\n\\n\\nOrdering Information:\\n\\n\\nAIM 334 – Slump Test Apparatus with testing rod & base plate\\n\\n

Country of Origin : India

Type : Lump Test Apparatus, Slump Test Apparatus

Condition : New

Application : Lump Testing

Design Features : Base Has Cleats For Better Ground Grip,Positive Clamping Of The Cone To The Base,Swivel Handle Acts As A Datum For Measurement

Replaceable Parts : Slump Cone - 1 No.,Base Plate With Swivel Handle - 1 No.,Tamping Rod, Steel, 16 Mm Dia X 600 Mm, ISI Certified - 1 No.

Ordering Information : AIM 334 - Slump Test Apparatus With Testing Rod & Base Plate

Saybolt Viscometer\\nAIM 529-1\\nRef. Standards – ASTM D88, D244, AASHTO T72 For the empirical measurement of Saybolt Viscosity of petroleum products at specified temperatures between 70°F and 210°F. This is also used for determining the Saybolt Furol viscosity of bituminous materials at temperatures of 250, 275, 300, 350, 400 and 450°F. It comprises one each of Cylindrical Oil Cup, Universal Tip, Furol Tip, Bath fitted with immersion heater mounted on a stand, Dimmerstat for temperature control, Stirrer with shield. Apparatus is supplied complete with insulated handle and thermometer support, receiving flask, withdrawal tube, filter funnel, thermometer support for cup and circular spirit level.\\nSuitable for operation on 220 V, 50 Hz, Single Phase, AC Supply.\\n\\nOrdering Information:\\n\\n\\nAIM 529-1 – Saybolt Viscometer with two cups - Digital\\n\\n\\n\\nOptional Accessories:\\n\\n\\nAIM 52910 – ASTM Thermometer Type 17F, Range: 66°F to 80°F\\n\\n\\nAIM 52911 – ASTM Thermometer Type 18F, Range: 94°F to 108°F\\n\\n\\nAIM 52912 – ASTM Thermometer Type 19F, Range: 120°F to 134°F\\n\\n\\nAIM 52913 – ASTM Thermometer Type 20F, Range: 134°F to 148°F\\n\\n\\nAIM 52914 – ASTM Thermometer Type 21F, Range: 174°F to 188°F\\n\\n\\nAIM 52915 – ASTM Thermometer Type 22F, Range: 204°F to 218°F\\n\\n\\nAIM 52918 – ASTM Thermometer Type 77F, Range: 245°F to 265°F\\n\\n\\nAIM 52919 – ASTM Thermometer Type 78F, Range: 295°F to 315°F\\n\\n\\nAIM 52917 – ASTM Thermometer Type 79F, Range: 345°F to 365°F\\n\\n\\nAIM 52919 – ASTM Thermometer Type 80F, Range: 395°F to 415°F\\n\\n\\nAIM 52920 – ASTM Thermometer Type 81F, Range: 445°F to 465°F\\n\\n\\n\\nReplacement Parts:\\n \\n\\n\\nAIM 52901 – Brass Oil Tube\\n\\n\\nAIM 52902 – Receiving Flask 60 ml\\n\\n\\nAIM 52903 – Universal and Furol Tip (set of 2)\\n\\n\\nAIM 52904 – Filter Funnel\\n\\n\\nAIM 52905 – Thermometer Support\\n\\n\\nAIM 52906 – Heating Coil\\n\\n

Type : Saybolt Viscometer

Color : Various Colors

Application : Measurement Of Saybolt Viscosity Of Petroleum Products And Saybolt Furol Viscosity Of Bituminous Materials At Specified Temperatures

Power Supply : 220 V, 50 Hz, Single Phase, AC Supply

Ring and Ball Apparatus\\nAIM 561-1 & AIM 561-2\\nThe Ring and Ball Apparatus is a compact user friendly apparatus. It has magnetic stirrer with heating facility and digital display of temperature, the heating can be adjusted through knob in AIM 561-1 and can be controlled through the integral PID controlled in AIM 561-2. Suitable for operation on 220 V, 50 Hz, Single Phase, AC supply.

Driven Type : Battery, Electric

Condition : New

Application : Industrial, Laboratory

Type : Compact User-friendly Apparatus

Country of Origin : India

Features : Magnetic Stirrer, Heating Facility, Digital Display Of Temperature

Heating Control : Knob Adjustment In AIM 561-1, PID Control In AIM 561-2

Power Supply : 220 V, 50 Hz, Single Phase, AC

Usage : Determining Softening Point Of Bituminous Materials

Modified Marshall Apparatus, 50 kN Single Speed AIM 550-4\\nRef. Standard ASTM D5581:2007 The Load Frame construction of the equipment is same as per AIM-552 but its capacity is 50kN and its mould size is 152.4mm dia. It is supplied with a Rammer of 10.21kg, Breaking Head, and sample ejector for 6" dia sample, as per the standard.\\nThe equipment consist of the following replaceable parts :\\n\\n\\nAIM 552 – Marshall Load frame 50kN\\n\\n\\nAIM 55001-152 – Breaking Head Stability Mould\\n\\n\\nAIM 55002-152 – Marshall Mould 152.4mm ID x 114.3 on high.\\n\\n\\nAIM 55003-152 – Base Plate for 152.4mm dia sample\\n\\n\\nAIM 55004-152 – Extension collar for 152.4 mm dia sample\\n\\n\\nAIM 55005-152 – Compaction Pedestal for 152.4 mm dia sample\\n\\n\\nAIM 55006-152 – Compaction Hammer 10.21kg x 457 mm drop\\n\\n\\nAIM 55007-152 – Load Transfer Bar\\n\\n\\nAIM 070518-152 – Sample Ejector for 152.4 mm dia Sample\\n\\n\\nAIM 052 – Dial Gauge 25 mm travel, 0.01mm least count\\n\\n\\nAIM 274 – Proving Ring capacity 50 kN\\n\\n

Type : Testing Equipment

Material : Steel

Application : Test The Stability Of Bituminous Samples

Mastic Asphalt Tester\\nAIM 592\\nRef. Standard BS 5284 & IS 1195 This machine is used to determine the hardness of asphalt material the design features direct vertical loading with loading weight that rest on thrust bearings therefore load is applied to the specimen without transmitting shock to the loading column. At the end of the loading period the depth of penetration of the pin can be read form the dial gauge to an accuracy of 0.01mm. The thermostatically controlled heater unit has a built in impeller which circulates the water to maintain an even temperature throughout.

Country of Origin : India

Asphalt Testing Equipment\\nPaving Mix Tests, Marshall Stability and Compaction\\nRef. Standards - ASTM D1559 / BS-598-197, EN-12697-34\\nMost frequently used test by highway departments, contractors, engineers, testing laboratories and governmental agencies is the stability test using Marshall Apparatus. The test is intended for the measurement of the resistance to plastic flow of cylindrical specimens of bituminous paving mixture loaded on the lateral surface. For use with hot mixture containing asphalt or tar and aggregate up to 25.4 mm maximum size. Suitable for operation on 220 V, 50 Hz, single phase, AC supply.\\n\\nMarshall Apparatus\\nAIM 550-1\\nSalient Features:\\n\\n\\nSingle Speed, Bench top load frame\\n\\n\\nMax. loading capacity: 50 kN\\n\\n\\nGeared Screw jack and Motor Drive\\n\\n\\nPrecise Speed\\n\\n\\nLimit Switch Protection for both upward and downward travel\\n\\n\\nUser friendly and easy to use controls. A thermal overload type Power Switch at the rear of the machine provides electrical protection. Platen movement is controlled from the front panel, by 3 push button switches, Up, Down and Stop. A Ball seated screw fitting located on the crosshead accepts load cells and load transducers up to and including 50kN. The equipment is a table top loading frame, with adjustable crosshead mounted on columns attached to sturdy base. The forces applied are generated by a screw jack via a reduction unit with worm gears housed in the base casting. Motor Power is from an electric motor via a multi-vee drive belt with platen speed of 50.8mm/min. The movement of arm is a grease packed oil assembly and should not normally require lubrication.\\n \\n 

Type : Marshall Apparatus

Material : Steel

Power : 375 W

Application : Asphalt Testing Equipment For Marshall Stability And Compaction Tests

Los Angeles Abrasion Testing Machine with Abrasive Charge\\nAIM 458\\nRef. Standards – IS:10070 This machine is for determining the resistance to wear off small size coarse aggregates and crushed rock. The machine consists of a hollow cylinder, mounted on a sturdy frame on ball bearings. A detachable shelf within it extends throughout the inside length of the drum, catches the abrasive charge and does not allow it to fall on the cover. The drum is rotated at a speed of 30-33 rpm by an electric motor through a heavy-duty reduction gear. Supplied complete with a tray for collection of the material.\\nSuitable for operation on 415V, 3 phase, 50Hz, AC Supply.\\nThe equipment consists of the following replaceable parts:\\n\\n\\nAIM 45801 – Abrasive charge, consisting of a set of 12 hardened steel balls of 48 mm dia\\n\\n\\nAIM 45802-1 – Digital controller box\\n\\n\\n  Ordering Information:\\n\\n\\nAIM 457 – Deval Abrasion Testing Machine\\n\\n\\nAIM 458 – Los Angeles Abrasion Testing Machine\\n\\n\\nNote: Los Angeles with canopy is also available on request.\\n  Flexure Test\\n \\nIt is essential to determine the flexural strength, resistance to wear, and abrasion properties of tiles for effective construction and quality assurance.

Voltage : 415V

Application : Determining Resistance To Wear Off Small Size Coarse Aggregates And Crushed Rock

Type : Los Angeles Abrasion Testing Machine

Laboratory California Bearing Ratio Test Apparatus\\\\nModel: AIM 120 – Motorised, Three Speed\\\\nReference Standards:\\\\n\\\\n\\\\nIS: 9669, IS: 2720 (Part XVI)\\\\n\\\\n\\\\nBS 1377: 1924\\\\n\\\\n\\\\nEN 13286-47\\\\n\\\\n\\\\nASTM D 1883\\\\n\\\\n\\\\nAASHTO 193\\\\n\\\\n\\\\nSpeed Options:\\\\n\\\\n\\\\nThree speeds: 1.5, 1.25, and 2.5 mm/min\\\\n\\\\n\\\\n \\\\nModel: AIM 120-MS – Two Speed with Mild Steel Moulds\\\\n\\\\n\\\\nSame configuration as AIM 120, except the moulds.\\\\n\\\\n\\\\nMould assembly including perforated base plate and extension collar made of Mild Steel (Zinc plated), not Gun Metal.\\\\n\\\\n\\\\nReplaceable Parts List:\\\\n \\\\n\\\\n\\\\n\\\\n\\\\nPart CodeDescription\\\\n\\\\n\\\\n\\\\nAIM 062-1\\\\nLoad Frame, 50 kN Capacity, Three Speed\\\\n\\\\n\\\\nAIM 12001-GM\\\\nMould – Gun Metal, 150 mm ID × 175 mm H\\\\n\\\\n\\\\nAIM 12002-GM\\\\nPerforated Base Plate – Gun Metal (for AIM 12001 Mould)\\\\n\\\\n\\\\nAIM 12003-GM\\\\nExtension Collar – Gun Metal, 150 mm ID × 50 mm H\\\\n\\\\n\\\\nAIM 12004\\\\nPenetration Piston – 50 mm Face Dia\\\\n\\\\n\\\\nAIM 12005\\\\nAdjustable Bracket for Penetration Dial Gauge\\\\n\\\\n\\\\nAIM 12006\\\\nCircular Metal Spacer Disc – 148 mm dia × 47.7 mm H, Detachable Handle\\\\n\\\\n\\\\nAIM 12007\\\\nAnnular Metal Weight – 2.5 kg, 147 mm dia with 53 mm dia Central Hole\\\\n\\\\n\\\\nAIM 12008\\\\nSlotted Metal Weight – 2.5 kg, 147 mm dia, with 53 mm dia Slot\\\\n\\\\n\\\\nAIM 12009\\\\nPerforated Plate – 148 mm dia, Adjustable Stem & Lock Nut\\\\n\\\\n\\\\nAIM 12010\\\\nMetal Tripod for Dial Gauge\\\\n\\\\n\\\\nAIM 12011\\\\nCutting Collar\\\\n\\\\n\\\\nAIM 11002\\\\nRammer – 2.6 kg, 310 mm Controlled Drop\\\\n\\\\n\\\\nAIM 11102\\\\nRammer – 4.9 kg, 450 mm Controlled Drop\\\\n\\\\n\\\\nAIM 274\\\\nProving Ring – 50 kN Capacity\\\\n\\\\n\\\\nAIM 072\\\\nDial Gauge – 25 mm Travel, 0.01 mm Least Count\\\\n\\\\n\\\\n\\\\n\\\\n\\\\n 

Type : Laboratory California Bearing Ratio Test Apparatus

Application : California Bearing Ratio Test

Crushing & Grinding\\nLaboratory Ball Mill\\nModels: AIM 441, AIM 441-10, AIM 441-20\\n \\nPurpose:\\nThe Laboratory Ball Mill is used for grinding pigments. It grinds materials to a specific fineness using a specific quantity of steel grinding balls over a defined period.\\n \\nApplications:\\n\\n\\nCement industry (for making ground cement samples)\\n\\n\\nPaint, plastic, granite, and tile industries\\n\\n\\n \\nFeatures:\\n\\n\\nIncludes revolution counter to monitor drum revolutions.\\n\\n\\nSupplied with recommended steel balls for 5 kg capacity:\\n\\n\\n\\n\\n\\n\\nDiameter (mm)Quantity (Nos.)\\n\\n\\n\\n40 mm\\n43\\n\\n\\n30 mm\\n67\\n\\n\\n25 mm\\n10\\n\\n\\n19 mm\\n71\\n\\n\\n12.5 mm\\n94\\n\\n\\n\\n\\n \\nPower Requirement:\\n\\n\\n\\n415V, 50Hz, 3 Phase, AC supply\\n\\n\\nNote:\\n \\nLiner with canopy for noise reduction is also available upon request.

Type : Laboratory Ball Mill

Model : AIM 441,AIM 441-10,AIM 441-20

Application : Cement Industries,Paint Industry,Plastic Industry,Granite Industry,Tile Industry

Features : Includes Revolution Counter To Monitor Drum Revolutions,Supplied With Recommended Steel Balls For 5 Kg Capacity

Asphalt Testing Equipment\\nDuctility\\nRef. Standards: IS:1208, ASTM D113, AASHTO T 51 Bituminous surfaces exposed to varying temperature conditions undergo a great deal of expansion and contraction. Therefore, an important characteristic of the binder is its ductility and the degree of ductility has an effect on the cracking of bituminous surfaces caused by traffic stress.\\nThe ductility of bitumen is expressed as the distance in centimetres to which a standard briquette can be elongated before the thread thus formed breaks under specified conditions.\\nA molten bitumen sample is poured into a standard mould, allowed to cool to room temperature and then placed in a water bath so that the briquette can be brought to test temperature before mounting in the testing machine.\\n\\nDuctility Testing Machine, Electrically Operated, Digital\\nAIM 565-1, AIM 565-DG & AIM 565-DG-C\\nDesigned to test three specimens simultaneously. The machine consists of a carriage moving over a lead screw. An electric motor with reduction gear unit ensures smooth constant speed and continuous operation. The entire assembly is mounted with water bath completely encased in metal bound hardwood. It is equipped with an electric pump circulator and heater. The temperature is controlled by digital temperature controller. Two rates of travel i.e. 5 cm/min and 1 cm/min are provided. Suitable for operation on 220 V, 50 Hz, Single Phase, AC supply.\\nThe equipment consists of:\\n\\n\\nAIM 56501 – Ductility Mould, with Base Plate 3 Nos.\\n\\n\\nOrdering Information:\\n\\n\\nAIM 565-1 – Ductility Testing Machine\\n\\n\\nAIM 565-DG – Ductility Testing Machine with digital display\\n\\n\\nAIM 565-DG-C – Ductility Testing Machine with digital display & cooling\\n\\n

Material : Metal, Hardwood

Digi Marshall Apparatus AIM 550-2\\nRef. Standards - ASTM D1559, ASTM D6927-06, BS 598-107, EN 12697-34 The AIMIL Digi Marshall Apparatus is used to test the Stability of bituminous samples, by highway departments, contractors, engineers, testing laboratories and other governmental agencies. Digi-Marshall Apparatus is used for measurement of the resistance to plastic flow of cylindrical specimens of Bituminous paving mixture loaded on the lateral surface. The machine can provide measurement data for use with hot mixture containing asphalt or tar and aggregate upto 25.4mm maximum size.\\nOrdering Information:\\n\\n\\nAIM 550-1 – Marshall Apparatus, 50kN, Single speed, New model for 4" dia sample\\n\\n\\nAIM 550-2 – Digi Marshall Apparatus, 50kN, Single speed, New model for 4" dia sample\\n\\n\\nAIM 550-3 – Digi modified Marshall Apparatus, 50kN, Single speed, New model for 6" dia sample\\n\\n\\nAIM 550-4 – Modified Marshall Apparatus, 50kN, Single Speed for 6” dia sample\\n\\n\\nAIM 550-5 – Modified Marshall Apparatus, 100kN Single Speed, New Model for 4”/6” dia sample\\n\\n\\nAIM 550-6 – Digi modified Marshall Apparatus, 100kN Single Speed, New Model for 4”/6” dia sample\\n\\n\\nOptional Accessories :\\n\\n\\nAIM 55020 – Electronic Conversion Kit for Marshall Apparatus\\n\\n\\nAIM 55021 – Electronic Conversion Kit for modified Marshall Apparatus Marshall Apparatus, 50kN\\n\\n\\nNote: Modified Marshall Apparatus, 100kN, Single Speed can also be provided.

Type : Testing Equipment

Application : Test The Stability Of Bituminous Samples

Moulding\\nInternational specifications for concrete strength testing require test specimens to be cast in various standard sizes for compression and flexural strength determination.\\nAimil moulds are made from high-quality metal, designed to:\\n\\n\\nResist distortion under rugged conditions\\n\\n\\nRetain shape and size accuracy\\n\\n\\nComply with standards: IS:10086, BS:1881, ASTM C31, ASTM C192, EN 12390-6-2\\n\\n\\nThese moulds feature:\\n\\n\\nHigh-precision internal surface finish\\n\\n\\nAccurate alignment during dismantling and reassembly\\n\\n\\nAimil provides a range of Cube Moulds, Cylindrical Moulds, and Beam Moulds.\\nCube Moulds\\nModels: AIM 343 & AIM 344\\nFour standard sizes of cube moulds are available and supplied with a base plate.\\n \\n \\n 

Application : Industrial Use

Type : Cube Mould

Material : Cast Iron

Moulding\\nAIM 414, AIM 417 & AIM 417-3\\nCube Moulds:\\nFor preparation of mortar and lime cubes, the following cube moulds are offered:\\nOrdering Information:\\n \\n\\n\\nAIM 414 – Mould, Steel, for 70.6 mm Cube with ISI Certification Mark as per IS:10080\\n\\n\\nAIM 417 – Mould, Cast Iron for 50 mm Cube with ISI Certification Mark as per IS:10086\\n\\n\\nAIM 417-3 – Mould Three Gang Cast Iron for 50 mm Cube\\n\\n

Type : Cube Mould

Material : Steel, Cast Iron

Size : 70.6 Mm Cube, 50 Mm Cube

Application : For Preparation Of Mortar And Lime Cubes

Model: AIM 9891\\nDescription:\\n\\n\\nDesigned for mixing concrete for test cubes.\\n\\n\\nEnsures uniform mixing of cement and aggregate.\\n\\n\\nAccepts aggregate size up to 20 mm.\\n\\n\\nSuitable for mixing dry or wet materials.\\n\\n\\nOperator-friendly access to contents; ribbed base and lift-up mixing paddles enhance usability.\\n\\n\\nSpecifications:\\n\\n\\nMixing Capacity: 40 litres\\n\\n\\nDimensions: 910 mm × 875 mm × 1250 mm\\n\\n\\nMotor: 2 HP\\n\\n\\nDrum RPM: 24 RPM\\n\\n\\nSpecial Features:\\n\\n\\nPortable and compact\\n\\n\\nAdjustable blades\\n\\n\\nEasy to clean and operate\\n\\n\\nPower Supply: 440V, 50Hz, Three Phase, AC\\nOrdering Info:\\n\\n\\nAIM 9891 – Concrete Mixer, Pan Type, Capacity 40 Litre\\n\\n\\n \\nNote: Higher capacity models of Pan Type Mixers are available on request.

Country of Origin : India

Type : Concrete Pan Mixer

Condition : New

Automatic Type : Automatic

Certification : ISO 9001:2008

Special Features : Portable And Compact. Adjustable Blades. Easy To Clean And Operate.

Model: AIM 9701\\nDescription:\\n\\n\\nSteel vessel with 30 L capacity mounted on a frame.\\n\\n\\nRotates at 20–24 RPM using a 1 HP motor or manually with a handle.\\n\\n\\nInternal blades ensure thorough mixing.\\n\\n\\nSteel frame mounted with wheels for portability.\\n\\n\\nSpecifications:\\n\\n\\nMixing Capacity: 30 litres\\n\\n\\nDimensions: 195 mm × 790 mm × 1370 mm\\n\\n\\nMotor: 1 HP\\n\\n\\nDrum RPM: 24 RPM\\n\\n\\nSpecial Features:\\n\\n\\nSimple to clean and maintain\\n\\n\\nEasy to operate\\n\\n\\nPower Supply: 220V, 50Hz, Single Phase, AC\\nOrdering Info:\\n \\n\\n\\nAIM 9701 – Concrete Mixer, Drum Type, Capacity 30 Litre\\n\\n

Country of Origin : India

Type : Concrete Mixers

Driven Type : Electric

Condition : New

Power Supply : 220V, 50Hz, Single Phase, AC

 \\\\nConcrete Testing\\\\nDigital Compression Testing Machines\\\\nModels: AIM 302E-DG-1, AIM 305E-DG-1, AIM 308E-DG-1, AIM 311E-DG-1, AIM 314E-DG-1, AIM 317E-DG-1, AIM 320E-DG-1\\\\n \\\\nPurpose:\\\\nDesigned for simple, economic, and reliable testing of concrete’s compressive strength. Emphasizes user-friendly operation, compact design, and easy maintenance—ideal for both lab and site applications.\\\\n \\\\nKey Features:\\\\n\\\\n\\\\nMeets IS:516, IS:14858 and ASTM, EN, BS standards (based on configuration).\\\\n\\\\n\\\\nPace Rate Indicator: Visual display for stress rate (Bar Graph).\\\\n\\\\n\\\\nAutomatic:\\\\n\\\\n\\\\nStress determination and display\\\\n\\\\n\\\\nOverload safety protection\\\\n\\\\n\\\\n\\\\n\\\\nSelf-aligning platen with quick change accessories.\\\\n\\\\n\\\\nConfigurable engineering unit and machine capacity.\\\\n\\\\n\\\\nFlexible Calibration: 5–10 calibration points.\\\\n\\\\n\\\\nTest Modes:\\\\n\\\\n\\\\nMode 1: Compression\\\\n\\\\n\\\\nMode 2: Flexure\\\\n\\\\n\\\\nMode 3: Prism\\\\n\\\\n\\\\nMode 4: Tensile Splitting Strength\\\\n\\\\n\\\\n\\\\n\\\\nCalibration and peak stress setting by shape and size.\\\\n\\\\n\\\\nPeak Load, Peak Stress, Unique Record No. displayed.\\\\n\\\\n\\\\nData Storage: ~2000 records.\\\\n\\\\n\\\\nUSB data download in ASCII format.\\\\n\\\\n\\\\nMenu-driven interface with Centronics dot matrix printer support.\\\\n\\\\n\\\\nDynamic Calibration with CVT for consistent voltage.\\\\n\\\\n\\\\n2% overload facility to calibrate full machine capacity.\\\\n\\\\n\\\\nSecure (Password protected) system & calibration.\\\\n\\\\n\\\\nUser functions: Start, Stop, Pause, Reset, Overload\\\\n\\\\n\\\\nMultifunction Keyboard for full control.\\\\n\\\\n\\\\n \\\\nSystem Description:\\\\n\\\\n\\\\nFully welded frame with:\\\\n\\\\n\\\\nTop crosshead\\\\n\\\\n\\\\nHardened and polished platens\\\\n\\\\n\\\\nSide walls\\\\n\\\\n\\\\n\\\\n\\\\nTwo-speed pump for fast daylight closure and precise control.\\\\n\\\\n\\\\nSelf-aligning action and spacers for multiple specimen types.\\\\n\\\\n\\\\nIntegrated digital display showing force/stress in SI, Metric, Imperial.\\\\n\\\\n\\\\nDisplay options in kN/sec or lb/sec.\\\\n\\\\n\\\\nLoad retention for ~15 min.\\\\n\\\\n\\\\nBuilt-in memory for ~2000 test results.\\\\n\\\\n\\\\nCalibration operating range: 10% to 100% of capacity\\\\n\\\\n\\\\nAccuracy: ±1% of applied load\\\\n\\\\n\\\\n\\\\n\\\\n 

Type : Compression Testing Machine

Material : Steel

Packaging Type : Standard Packaging

Application : Testing Concrete Compressive Strength

Cannon Manning / Fenske Viscometer\\nAIM 532, AIM 532-1, & AIM 532-2\\nRef. Standard: IS 1206 (II) & IS 1206 (III)\\nCannon Manning Viscometers are designed for the determination of the absolute viscosity of bitumen & cutbacks by a vacuum capillary method at specified temperatures. Cannon Fenske Viscometers are designed for the determination of the kinematic viscosity by a vacuum capillary method.\\nVarious types of Glass capillary Viscometers are used to measure viscosities because no single capillary Viscometer is ideally suited for all viscosity determinations.\\nSuitable for operation on 220 V, 50 Hz, Single Phase, AC Supply.\\n \\nFeatures (Technical Specifications)\\n(a) Cannon-Manning Viscometer:\\n\\n\\nUsed for the measurement of absolute viscosity of highly viscous materials\\n\\n\\nViscometers of sizes 12 & 13\\n\\n\\nApplicable to materials of viscosities in the range of 360 to 8000 poise\\n\\n\\n(b) Cannon – Fenske Viscometer\\n(BS U Tube modified reverse flow Viscometer):\\n\\n\\nGenerally used for the measurement of kinematic viscosity of transparent or translucent liquids\\n\\n\\nViscometer of size 6 with direct flow range of 60 to 100 cSt\\n\\n\\nViscometer of size 7 with direct flow range of 180 to 3000 cSt\\n\\n\\n \\nMajor Components:\\n\\n\\nCannon – Manning Capillary tubes of sizes 12 & 13\\n\\n\\nCannon – Fenske Capillary tubes of sizes 6 & 7\\n\\n\\nKinematic Viscometer Bath with a provision for 6 tests\\n\\n\\nVacuum system\\n\\n\\nThermometer of IP-5C: range from –2 to 300°C (as per specification)\\n\\n\\nThermometer IP–64C: range from –20 to 102°C (0.2° resolution)\\n\\n

Type : Viscometer

Color : Transparent Or Translucent

Uses : Measurement Of Viscosity Of Bitumen, Cutbacks, And Liquids

Buoyancy Balance Model: AIM 9933 Purpose:\\nUsed to quickly and accurately check the density of hardened concrete specimens like cubes and cylinders.\\n  Construction & Features:\\n\\n\\nThe Buoyancy Balance consists of:\\n\\n\\nA water tank mounted on a platform.\\n\\n\\nA mechanical lifting device integrated into a rigid support frame.\\n\\n\\n\\n\\nThis setup allows specimens to be suspended below the balance for submerged weighing (for determining volume via displacement).\\n\\n\\nThe balance can also be used as a standard laboratory weighing system.\\n\\n\\n  Technical Specification:\\n\\n\\nCapacity: 15 kg\\n\\n\\nAccuracy: ±0.5 g\\n\\n\\n  Power Supply:\\n\\n\\nOperates on 220 V, 50 Hz, Single Phase, AC supply\\n\\n\\n  Ordering Information:\\n \\n\\n\\nAIM 9933 – Buoyancy Balance\\n\\n

Type : Buoyancy Balance

Model : AIM 9933

Construction : Water Tank, Mechanical Lifting Device

Features : Submerged Weighing, Laboratory Weighing System

Capacity : 15 Kg

Power Supply : 220 V, 50 Hz, Single Phase, AC Supply