Industrial Control System Dealers in Warje, Pune

Load sharing panel. These panels have been used for AMR applications as well as generator parallelity and mains and generator synchronizing. Accusonic is a pioneer in providing synchronizing solution using comap generator synchronizing products.

Suitable for Submersible Pump & Open well Pump Protections against Over load & Dry Run with Starting & Running Capacitors. Input Voltage -230 VAC. Current Capacity -25 Amps. Max. Current Setting- 16 Amps. Max. Available for 0.5 H.P., 0.75 H.P., 1 H.P., 1.5 H.P. and 2 H.P.

Engaged in the trade of supplying the excellent product range, we are efficiently operating from Maharashtra(India). With our modern transportation facility, timely and safe deliveries are guaranteed with us.

Level control system Maintaining the optimum level control system in the feed water tank is very important in order to ensure maximum temperature in feed water tank from condensate recovery & ensure the safety of the boiler. To achieve this without manual intervention, level control system is used. We offer a customized Level Control Systems for Boiler Feed water tank where hot condensate is preferred & utilized maximum, then hot water from any other sources & last preference to the cold make up water. This ensures that the energy of hot condensate & hot water from other sources is utilized

We carry out the quality examinations only under the vigil supervision of the quality auditors. As a famed organization in Maharashtra(India), we make sure that our customers will receive their orders at their preferred destination.

Close loop system comes with Lambda Controller ECUstepper motor MPFI emulator, this system has complete automatic gas regulation and it also depends on what the car engine requires apart from that it emulates the lambda O2 readings to the main car ECU to prevent engine check. Many people opt for Close loop systems because the mileage & pick up is better… For Better Mileage and Smooth Performance : Lambda Control System is a computerized self registering electronic system for the management of Natural Gas. It is n antipollution computerized device which controls of emission of MPFI cars.Lambda Control System maintains the stoichiometric ratio of the fuel setting constant through the acquisition of the Lambda probe signal of vehicle. It optimizes driving parameters during the transitory phases in acceleration and in deceleration.Lambda Control System it does not require manual adjustment and is capable of adapting automatically to changing environmental condition and different vehicle uses ensuring and optional carburetion in terms of drive-ability consumption and demission.Lambda Control System electronically manages the adjustment of the flow rate of Gas, allowing the Lambda factor to reach desired levels at all engine revolution rates.Lambda Control System Electromechanical actuator dosing the amount of gas at medium and high regimes. (At-Max.) Keeping it constant even when other system is running such as air conditioning, Power Steering etc.

Focusing on the hazards caused by fire in industries, homes, offices, hospitals and many more places an intelligent fire alarm is introduced. Intelligent fire alarm panel is an active fire detection system. As it detects fire it immediately gives an alarm. As it is also provided with gsm service, it will alert you by sending a sms as well as a voice call on the registered mobile number. Its auto dialer works with fixed gsm (sim) network. It helps in taking the fire-protection measures in time.

Up to 31 DCCS controllers can communicate with a Centralized PC using RS 485 Party Line subject to 240 circuits in all. Accuracy: +/- 0.2 % Typical (Depends on the sensors used) Program storage 60 steps per program. No. of programs on PC : 1000 Status of all circuits in the selected group can be monitored. Status display shows: Voltage, Current, Time, Program No., Step No., AH, WH, Temperature. Step Commands: Charge, Discharge, Pause, Charge/Discharge Ramp, Registration ON/OFF, DAT, End of Cycle / EOF, Set Amp-Hr, Set Watt-Hr. Loop. Step Control parameters: Current, Voltage and Temperature (Any two parameters can be programmed in one step). Step Termination parameters: Voltage, Amp Hr, Watt Hr., Temperature With less than OR Greater than option, Loop count, Time. (Any One OR Two parameters can be programmed & action will be effected on whichever is effective earlier) Program Abort Parameters: Voltage, Amp Hr, Watt Hr., and Temperature. (Any One OR Two parameters can be programmed & action will be effected on whichever is effective earlier) Step Registration can be done on Time, Amp Hr, Watt-Hr, Temp and Voltage. Data is also registered automatically on User Interruption, Power Resume, and other errors. Local Storage of 40 Programs which can be used for offline operations Maximum allowable current is programmable for each circuit. START, STOP, and CONTINUE selected circuits from LCD MMI also. Circuit status and Input / Output monitoring from LCD MMI. The Distributed Charger Control System (DCCS) is a complete system for controlling multiple chargers. The system not only controls but also registers data from each battery bank at programmed events. This gives a complete control solution for charging / formation process. Operator can monitor, control multiple circuits from a single PC using friendly Windows based software. Current, Voltage and/or Temperature can be controlled with Time, AH, WH, Temperature and/or Voltage as terminating conditions.   Salient Features: Each DCCS controller can support up to 24 circuits. Windows based PC Software for Program editing, down loading, monitoring of circuit parameters, Registration, etc. Data registered is available in CSV format, which can be used with any database software such as MS Excel etc.

we offer Power Distribution Board. these are used to distribute power among all the sections as per system requirement. main incomer & outgoing feeder ratings are decided as per load requirement of particular section. busbars used as mains & interconnection are either of copper or aluminium as per customer specifications.

We are offering fire pump panel. - diesel engine based fire pump panel - engine and pump protection - using microprcessor based controller - customization is possible

Relay and metering panels are used to control HT breaker on remote operation. It contains various protective relays required for the system and metering to measure electrical parameters.

We offer automatic power factor controller. We are a leading manufacturer & exporter of automatic power factor controller such as relay pfc controller, power factor controller, automatic power factor controllers and power factor correction devices from india.

Auto mains failure (AMF) Panels is meant for controlling DG START / STOP sequence in accordance to the availability of utility power supply. It has a relay sensor that detects power failure & shift the load to a generator. If power being resumed same relay sensor detects is & shift the load back to the supply. AMF control system provides continuous flow of power supply to the load in case of power failure & fluctuation

Solar Power Panel, Solar Energy Panel, Hand Held Metal Detector

Combustion Systems, Industrial Burners, LOw Nox Burners, Baffle Burner

Metering Cubicles, Electrical Surface Box, Multi Plug, Discharge Electrod

Fire Fighting Panels, Fire Fighting Equipment

Electric Control Panel, UPS Stabilize

TC Panel Manual Switch, Low Pressure Switches, 20 NB Manual Multiport Valve

Synchronization Panel, Automation Panel, Distribution Boxe