Density Testing Equipment Dealers

SAND REPLACEMENT METHOD: Three sizes Available.10cm (Small Size) :- Sand Replacement Method. Consists of Sand Pouring Cylinder, one calibrating container 10 cm dia & a square tray of 30 cm x 30 cm with a central hole of 10 cm diameter. Relevant Standard : IS : 2720(Part-XXVIII),15cm (Medium Size) : Sand Replacement Method. Consisting of Sand Pouring Cylinder container metal tray hole in the centre.20cm (Large Size) : Sand Replacement Method. with calibrating container of 250mm internal depth, one metal tray 450 mm square and 50 mm deep with a 200 mm dia hole in the centre.

The bulk density measurement is used for determining the weight per cubic meter of freshly mixed concrete (density of concrete) from which the yield of concrete per cubic meter can be calculated.Procedure for measuring bulk density of concrete is as per IS 1199 – methods of sampling and analysis of concrete. The steps are as follows:i) Take freshly mixed concrete from transit mixer by using wheel borrow.ii) Fill the cylindrical measure with concrete as soon as practicable after mixing.iii) Fill the cylindrical measure with concrete in layers approximately 5 cm deep and each layer shall be compacted.iv) While compacting the concrete the standard tamping bar shall be distributed in uniform manner over the cross section of the measure.v) The number of strokes per layer is 60 for 10 litres cylinder and 120 for 20 litres cylinder.vi) The exterior surface of the cylinder shall be tapped 10 to 15 times or until no large bubbles of air appear on the surface of the compacted layer.vii) Strike-off the top surface and finish it smoothly with a flat cover plate.viii) Clean all excess concrete from the exterior and weigh the filled measured.ix) Density of concrete : The weight per cubic meter of concrete shall be calculated by dividing the weight of fully compacted concrete in the cylindrical measure by the capacity of measure in kg/cu.m.x) Yield of concrete (V2) : The volume of concrete produced per cum. shall be calculated as follows.= Weight of cement, kg= Weight of fine aggregate, kg= Weight of coarse aggregate, kg= Weight of water, kg

The equipment is assembled in a mild steel cabinet attractively painted. A central shaft carries a platform with the glass cylinders of 50 ml. each. The platform with the glass cylinders moves up and down at 30 strokes per minutes through a distance of 5 cm and strikes on rubber cushioned bed. Electrically operated, supplied with time switch 0-15 minutes.

Digital reading of strokes. Housed-in powder coated body to hold two cylinders of 50 ml. Max strokes settable 999. Supplied without measuring cylinder

Specially designed to study, the packing down of powder beds of different pharmaceuticals and chemicals in the process of tablet manufacturing, capsule filling & cosmetics. Installed with an automatic device for preset of strokes. Gear driven Noiseless and strudy motor, also provided with an electronic timer. Elegantly designed for smooth operation electrically operated on 230v AC, 50 Hz.

Smoke & FTIR Toxic Gas Analyzer – EN 45545-2, ISO 5659, ASTM E662 | KDM Global KDM Global manufactures and exports a high-precision Smoke & FTIR Toxic Gas Analyzer designed for fire safety testing as per EN 45545-2, ISO 5659-2, and ASTM E662. This advanced testing system is ideal for railway component testing, polymer and cable material evaluation, and OEM lab certification under national and international fire standards. Our equipment integrates optical smoke density measurement with FTIR (Fourier Transform Infrared) spectroscopy, offering real-time analysis of toxic gases released during material combustion. It is widely used in railway fire testing labs, government-approved facilities, test agencies, and in-house R&D labs across India and export markets. Key Features Dual-function system: Combines smoke density testing (ISO 5659-2) with FTIR-based gas analysis Compliance ready: Fully meets EN 45545-2 Annex C, ISO 5659-2, ASTM E662, and NF X70-100 FTIR gas detection: Accurately quantifies toxic gases including CO, CO₂, HCl, HCN, NO, NO₂, SO₂ Real-time output: Continuous data logging with gas concentration curves and toxicity index (CIT) calculation Flexible heat source: Radiant panel with both 25 kW/m² and 50 kW/m² configurations User-friendly software: Includes automated reporting, calibration, and spectral interpretation Export-ready system: CE-marked, ISO-certified, and supplied with international packaging and documentation Technical Compliance EN 45545-2 Annex C: Railway material toxicity testing for HL1, HL2, HL3 classification ISO 5659-2: Smoke production testing under controlled radiant heat ASTM E662: Smoke and gas emission under flaming and non-flaming conditions NF X70-100: FTIR-based gas analysis method Applications Railway coach and metro interior testing Evaluation of polymers, composites, foams, cables, and coatings Certification labs for EN, ISO, BIS, ASTM flammability standards Electrical component manufacturers and metro rail suppliers Government and private fire testing laboratories Why Choose KDM Global Leading Indian exporter of EN 45545-2 compliant fire testing equipment In-house manufacturing of ISO 5659 + FTIR integrated machines Installation, training, and calibration included Custom configurations for OEMs and turnkey labs AMC and remote service support available worldwide Successfully installed in metro projects, OEMs, and certified labs across India

Smoke Density Apparatus is used for measuring & observing the relative amount (Density) of smoke produced by the burning (combustion) or decomposition of Plastic, Cables etc. under controlled conditions.Smoke Density Test Apparatus is used for measuring & observing the relative amount (Density) of smoke produced by the burning (combustion) or decomposition of Plastic, Cables etc. under controlled conditions.

EN 45545-2 Smoke Density & Visibility Testing Systems – Low Visibility & Smoke Chamber Equipment Accurate Smoke Density and Visibility Testing Solutions for Railway Fire Safety Compliance KDM Global offers advanced EN 45545-2 compliant smoke density and visibility testing systems designed to measure smoke obscuration and visibility loss during fire scenarios in railway interiors. These systems are critical for assessing smoke production from materials used in trains, metro coaches, and other rolling stock to ensure passenger safety and regulatory compliance. ✅ Standard Compliance: EN 45545-2 – Railway fire safety standard for smoke density and visibility ISO 5659-2 – Determination of optical density of smoke generated by solid materials Supports classification under hazard levels HL1, HL2, HL3 as per EN 45545-2 🔍 Applications: Testing railway seat foams, wall panels, flooring, and ceiling materials Smoke density evaluation of insulation, cables, and composite materials Material qualification for railway interiors and rolling stock components Certification laboratories and fire safety R&D centers 🔧 System Features: Precision-controlled smoke chamber with calibrated optical sensors Real-time optical density measurement and visibility analysis Automated data acquisition with comprehensive test report generation Configurable sample holders to accommodate various material sizes Optional integration with FTIR for simultaneous toxic gas analysis 🏆 Why Partner with KDM Global? Equipment fully compliant with EN 45545-2 smoke density testing requirements Reliable, repeatable, and easy-to-use test systems built for industrial labs Expert support including installation, calibration, and on-site training Widely used by railway OEMs, testing labs, and certification agencies 📩 Request Your Customized Quote Today Ensure your railway interior materials meet stringent smoke visibility standards with KDM Global’s EN 45545-2 smoke density testing systems.   📧 Email: saleskdmglobal@ 📞 Phone: +91 / +91 🌐 Website:

Optional Liquid Density kit is used with MD300S / SD200L to find the density of Liquid Samples having less than 100 Centipoise of viscosity by changing the code setting in the machine and using the Liquid Kit, 50cc Liquid is poured in a Glass Beaker and Density can be measured in 30 secs. using the Liquid Kit.

Density Meter DM-250.3 LPGDi Ex   Unique Portable Density Meter is a new development especially for liquefied petroleum gases (LPG) measuring. It is based on the resonant method of density measurements and uses small sample volume. Obtained results are instantly converted to relative density (15°C or 20°C or 60°F) in accordance with ASTM D1250 tables.   Features - Precise density and temperature in seconds - Excellent correlation to ASTM D1657 - Small sample volume - Easy to operate - Direct density measurement - Small and compact - Automatic temperature compensation - Data transfer to PC via Bluetooth

Specially designed to study the packing down of powder beds of different powders fitted with Digital Counter facility, starts automatically on attaining the pre-set strokes provided without Graduated Glass Cylinders of 50/100 ml capacity.  

BULK DENSITY APPARATUS : P-B7 To determine the density of the powder graduated cylinder holded in clamps moves through motor up and down direction at a frequency rate between 28/32 cycles per minute through a distance of 5-6 cms. which strikes on a cushion fitted on the platform. A timer is provided to set the duration. Bulk Density Apparatus :P-B7A : With digital preset revolution counter. The instrument will stop after setted revolutions. Additional Information: Item Code: P-B7