Distribution Transformers Dealers in Thane

  Oil cooled transformers are made for use on various systems ranging from 11kv to 33kv. the basic construction of the CT is similar to CT of all voltage classes in that the core is placed in a tank mounted on top of the bushing and adequate paper insulation is provided on it. The secondary leads are run through the bushing to the secondary terminal box placed at the bottom of the bushing.   The advantage of this type of construction is that the transformer is dynamically more stable under short circuit conditions, the various forces on the primary conductors tending to balance on another. Requisite number of the primary turn are put on the core and the two ends are bought out for connection into the system. The primary ends are terminated on the terminals 30 mm dia 80mm long for easy connection into the system.In the case of two ratio current transformer in which the different ratios are obtained by primary reconnection, four primary terminals are brought out on the tank(corresponding to the two primary windings) and these are connected in series or parallel, by connecting links provided depending upon the ratio required. The transformers are fully sealed in construction and are supplied filled with required quantity of oil. Adequate allowance is made for expansion of oil due to temperature variations and as such a breather is considered unnecessary.

In order to furnish the varied requirements of our patrons, we are engrossed in offering an extensive assortment of Electrical Transformer. Entire array of transformer we offer are up to 2000 KVA and 11+22+33 KV/433 Voltage Class MSEB Specification. All out products are precisely engineered at our end with the help of sophisticated machines and using top-notch grade raw material which is been procured from certified vendors of the market.

A Control Transformer supplies power to control and / or auxiliary equipment not intended for direct connection to the main source. Control Transformers are specifically used to provide control supply voltage for the control circuits of AC motor starters i.e. starter coils, timers, indicating lamps electronics protection relays etc. Control Transformers for contractor applications have to energize the coils. It should have good regulation for surge current. Control transformers are mostly used for industrial applications where electromagnetic devices such as contractors, relays and solenoids are used. They are also used in less sensitive devices where accurate secondary low voltages are essential. The Control Transformer maximizes inrush capability and output voltage regulation when electromagnetic devices are initially energized. Control transformers are sometimes called Industrial Control Transformers, Machine Tool Transformers, or Control Power Transformers.

Three-phase transformers are one of the work horses of a power transmission and distribution system. They are actually among the most often used on the transmission part of the system and are also an integral part of the industrial distribution system.

  1 60 kVA 11 kV Class to 10,000 kVA, 33 kV Class suitable for both Indoor Outdoor applications with Off Circuit Tap Links, Off Circuit Tap Switch, On Load Tap Changer (Indigenous & Imported)   The Cast Resin Transformer are manufactured to comply with National International Standards BISI IS 11171, IEC 60726.   HOTELS & HIGH RISE BUILDINGS DEFENCE ESTABLISHMENTS HOSPITALS THEATERS PORTS & DRY DOCKS PRODUCTION PLANTS AIRPORTS MINES STEEL PLANTS DRILLING SHIPS & OFF SHORE RIGS SEB'S & UTILITES METRO & CONVENTIONAL RAILWAYS NUCLEAR POWER STATIONS & RESEARCH CENTRES MAINTANENCE. FREE NON TOXIC NON INFLAMMABLE NON HYGROSCOPIC HIGH RELIABILITY HIGH SURGE VOLTAGE WITHSTAND HIGH SHORT CIRCUIT STRENGTH HIGH OVERLOAD CAPACITY LOW PARTIAL DISCHARGE RESISTANT TO TEMPERATURE FLUCTUATIONS SMALLER SIZE / WEIGHT LOW NOISE LEVEL LOW OPERATING COST COST EFFECTIVE

We are offering distribution transformer used at control panels , battery charges , stabilizers , cranes , etc.

Oil Cooled Power Transformer, Heat Treatment Transformer, Ferrite Transforme

Oil Cooled Distribution Transformer, Dry Type Transformer

We provide all types of distribution transformer fabrication service at our company.as per the customer requirement and drawing and size.

2000 kva 11v oltc transformer.

Compact Substation, Cast Resin Dry Transformer, Rectifier Duty Transformer

Three Phase Variable Transformer, Electrical Motor, Transforme

Distribution Transformer

Electrical Transforme

Oil Cooled Distribution Transformer, Power Transformers, Dry Transformer

Oil Immersed Distribution Transforme

Three Phase Transformer, Capacitor Panel, Motor Control Centr

Solar Transformer, Power Transformers, Special Purpose Transforme