Soil Testing Equipment Dealers in Kathwada, Ahmedabad (12 products available)

• Brand Name: EIE

We are offering standard penetrometer. As per is 1448(p-92),is 1448(p-93),is 7401 ip 49 & 50, ip-179, ip-376, astmd 1321, astm d 937 this apparatus is used for penetration test on a wide variety of materials such as grease, petroleum, bitumen, tar, wax, olish, foodstuff, rubber asphalts and pharmaceutical creams. A depression is made in the sample by a needle of a definite weights which is measured intenths of a millimeter and expressed as penetration number. the apparatus consist of a cast aluminium base with an iron stand on which moves an aluminium arm and brass chromium plated rod slide through the lower portion of the arm. A needle with weights is fitted to this rod. The penetration value and penetration time is indicated on digital panel with least count on 0.01mm. Supplied complete with adjustable needle holder, penetration needle, sample container, transfer dish and weight of 50 gms. Salient features. * with geared arrangement for moving the arm with geared unit. * provision to readout penetration value & time of process. * penetration value in 000.0 * penetration value maximum up to 500.0 (50.00mm) * panel cut out size : 92 x 188 mm. * provision to set the time value of from 0.00 to 99.99 sec. * the timer output is 300v dc without load. * provision for tare for penetration. * provision for calibration. * provision for default calibration. * with pcprinter interface with software fir direct printout of calculated results (at extra cost) at extra cost bitumen container 55 mm x 35 mm bitumen container 70 mm x 45 mm bitumen container 55 mm x 57 mm brass cone aluminium solid cone weight (50gms or 100gms) grease container 10 cm dia & 10 cm height bath for penetration test.

Introduction Hand operated With Automatic Timer Hand Operated : The apparatus consist of a cast aluminium base with an iron stand on which moves an aluminium arm. A 6" dial is fixed on this arm and a brass chromium plated rod slide through the lower portion of the arm. A needle with weights is fitted to this rod. The dial is graduated from 0-400 in one tenth millimeter sub division. Supplied complete with adjustable needle holder, penetration needle sample container, transfer dish and weight of 50 gms. With Automatic Timer : Same as above but with automatic digital timer and electrical arrangement.

• Temperature Range: 0-400 deg °C.
• Model No.: ESCR- A
• Time totaliser range: 999.9 hours
• Accessories: Cutting die, nicking jig, bending cum transfer tool, specimen holder, test tube & rubber cork
• Water circulation: Through induction motor with stirrer
• Testing capacity: 6 tests at a time
• Heating load: 1.5 to 3 KW
• Body: Inner S.S and Outer M.S with powder coating
• Power Supply: 230V AC, 50Hz
• Inner size of bath: 12"X 8"X 9"
• Dimension: 28"X 13" X 25"
• Net weight: 36 kgs

• Automation Grade: Automatic
• Application: For Siol Laboratory
• Weight: 5 kg
• Voltage: 230 V
• Finishing: Powder Coating
• Brand Name: DM
• Display Type: Analoge and Digital
• Power: Electronic
• Material: Mild Steel
• Precision Cone Penetration: +- 0.1mm
• Maximum Range: 70mm

Mett-Bio Metallurgical Testing & Services with its state of the art equipment setup consisting of Salt Spray Chamber Complying to the Requirement of ASTM B 117/ ASTM G 85.   Tests are performed in our ISO 17025:2005 NABL accredited lab under the standard Specified conditions or as per specific field conditions.   Salt spray testing is a test method where in a product or coatings resistance to corrosion is evaluated in severe corrosive conditions with extended exposure to a saline or salted spray   This testing is carried out in a closed chamber which is filled neutral salt fog. The test specimen is exposed to a predetermined time period and inspected during its exposure. This test is carried out to check the integrity of coatings, paints in a corrosive environment. This test is carried out as per ASTM B117.   Types of Salt spray testing:   · Neutral Salt Spray (NSS), · Acetic acid Salt Spray (ASS), · Copper sulphate Acetic Salt Spray (CASS)   The salt spray test can be acclimatized to suite different corrosivity level to simulate different environments.   The test specimen is exposed to a predetermined time period and inspected during its exposure. This test is carried out to check the integrity of coatings, paints in a corrosive environment. This test is carried out as per ASTM G 85.   A standard 5% salt solution of sodium chloride known as NSS or neutral salt spray and a solution of acetic acid known as ASS. The solutions are chosen based on the type of coating to be evaluated   Other salt variations: SO2 / Calcium Chloride (CaCl2)

• Ground Glass: 10mm thick and about 45 cm square or larger rough glass as per IS 2720 (Part V-1985) for mixing soil and water
• Spatula: Flexible with blade about 8 cm long and 2 cm wide made from stainless steel material as per IS:2720 (part V-1985)
• Evaporating dish: Made from porcelain material having diameter of about 12 to 15 cm with smooth surface as per IS 2720 (part V-1985)

  Introduction Used to determine the flakiness index of the aggregate. The aggregate particles are to be considered flaky, if their thickness is less than 0.6 of their nominal size.It consists of a frame with sliding panel with accurate slots of different standard width and length, the complete assembly is chrome plated or powder coated.

We are passionately engaged in offering an exclusive range of Salt Spray Test Chamber. These test chambers are inspected by a team of vendor’s quality experts against various quality parameters so as to dispatch a flawless range. We provide these test chambers in different specifications as per the variegated needs of our clients. Besides this, our given test chambers are highly acclaimed among our customers for its long lasting performance.

ESCR Test Apparatus: Environmental stress cracking is a property that is highly dependent upon the nature and level of stress applied and on the thermal history of specimen. This taste is normally employed for routine inspection purpose.   

• Type: Laboratory Furniture
• Material: Mild Steel
• Voltage: 220/230 Volts AC Supply

Fabricated out of thick Mild Steel Sheet these are designed so as to throw out toxic/harmful vapours, thus protecting costly instruments & the person working in the lab. The outer surface is finished with powder coated & inner surface is epoxy painted.   The working table top is fitted with acid/alkali resistant tiles/S.S & a small wash basin with connections provided for inlet & outlet of water. The front door moves vertically up & down with concealed counterbalanced weight. The unit is fitted with fluorescent light & a gas cock of gas/air supply. The space under the work station can be provided with storage compartments for storage purpose. The front-facing panel is fitted with 15/5 amp socket with switches for exhaust system & fluorescent light to work on 220/230 volts AC Supply.

Soil Testing Equipment, Digital Comparators