Testing Machines Dealers in Ahmedabad

With refrigeration system and micro-processor based digital temperature controller Ductility is defined as distance in cms to which a standard briquette of bitumen can be stretched before the thread breaks. The briquette is stretched at a rate of 50 mm/min.± 2.5mm per minute at a temperature of 27°C ± 0.5°C The Machine is having built in refrigeration system to work a below ambient temperature up to 10°C in tropical conditions. The Machine will operate at 27°C with control accuracy of ± 0.5°C as per the requirement of IS. The apparatus consists of water bath with a heater, and a circulating pump to maintain uiform water tempetature . one half of the briquette moulds is fixed in a fixed plate in the water bath, the other half of the briquette mould is fixed to a carrier which slides over a rotating threaded shaft with a clutch, The motor and gears to rotate the shaft are housed in a cabinet fixed above the other end of the bath. A pointer fixed to the carrier moves over. a scale graduated from 0-100 cm x 1mm fixed on the bath with "0" (Zero) of the scale towards the fixed plates side. The rotating shaft has 2 speeds of travel for the bracket, 5 cm/min.and 1cm/min. selected by a clutch. Water bath inside is of stainless steel with insulation and water drain cock . A heater with is fitted inside the water bath. The Temp. is controlled by dual display Microprocessor based Auto Tuning PID Digital Temp. indicator cum controller. Control switches for motor, stirrer, heater and indicator lamps are fixed at a convenient place on the water bath. Complete with three briqutte moulds and one base plate, All supply single phase. As per IS 1208.

This Instrument is in according to ASTM BS, DIN, ISO, ISI (Indian Standard) or according to customer’s required specification. Maximum pressure range 0-99.99bars. Fully Microprocessor based pressure controller to maintain the pressure with in 0.5% accuracy of full scale Fully hydraulic system with central pressurized water supply Reliable high-pressure water pump with operating pressure up to 100/200 bars User-friendly data logging software provided with machine to record data and able to get graph plotting as well as database on each stations separately Data record facility of all stations pressure as well as temp of one channel temperature controller Presentation of report in table format graphical forms Test can be conducted if power failure Air less motorized pumping stations is provided to build the pressure very fast All stations are provided with the QRC coupling to save preparation time Each station is equipped with the high reduce solenoid with the manual and auto operating modes Trip point value is selectable provided to indicate the failure and auto stop at particular station in case of the failure of the pipe or any leakage from the end plugs In built calibration facility of pressure transducers is provided with the pressure controller Auto protection of pressure transducers is also in built feature and a part of machine  

The Izod / Charpy Impact Test is used to measure the relative susceptibility of standard test specimen to the pendulum type Impact load.   The "Saumya" Izod / Charpy Impacto Meter is having a energy range from one joule to twenty-five joules in five different scales.     STANDARDS:   ASTM D 256 AND OTHER EQUIVALENT STANDARDS     APPLICATION:   Impact Strength is the Mechanical property of polymer and as molecular flexibility plays an important role in determining the relative toughness of materials. For any molded plastic this test plays an important roll.   USP:   The "Saumya" Impacto Meter is designed and built according to National and International Standards. Dial with clear and five different scales for energy selection.   The "Saumya" Digital Imecto Meter is having versatile features with high accuracy to measure Izod / Charpy Test upto range of 1 to 25 Joules.   Interchangeable parts for Izod and Charpy test.   Two hammers each for both the test with extra load attachments.  

The digital compression testing machine has been designed to meet the need for a simple, economic and reliable means to test concrete for its compressive strength. The design expressive of simplicity, both of construction and operation, makes the machine easy to use and maintain. The unit is compact, making it useful for site and Laboratory applications. The digital machines are provided with a pace rate controller, to enable maintain a constant of loading. Features High stability four column load frame Each frame tested for stability and alignment to avoid tension failure during a test and to ensure centre loading Standard Platens for 3 X 6”/ 4 X 8” and 6 X 12” cylinders included. A precise large diameter spherical upper platen for optimum results Variety of optional accessories for cubes, blocks, bricks and flexure test available Motorized hydraulic power pack or pumping unit with rapid approach and automatic overload protection Comes standard with safety Guards on all four sides. The Complete unit comprises a Loading Unit which is of fully welded or two pillar model construction having a cross-head with a spherical seated platen. The lower platen is attached to the top of the piston. The Loading capacity is of 2000 KN, Cubes up to 200 mm & Cylinders up to 150 mm Dia X 300 mm Height can be tested using the appropriate spacers. Pumping Unit with choice of compact power pack attached closely to the loading unit or separate hydraulic pumping unit, attached to the loading unit by high pressure hydraulic flexible hose pipe. The pump facilitates rapid approach of the platens for daylight closure and also provides comprehensive control over the application of load. A control valve provides fine control over the loading rate for accurate pacing. Maximum load is held and retained for approx. 15 min, unless cancelled, using the panel mounted reset switch. Pace rate set for running the test can be maintained manually. Model With digital Readout and pace rate Controller Type of Pumping Electrical Loading Range 2000KN Least Count 1 KN Max. Clearance Between Platen 370mm Max. Clearance Between Side Platen 340mm Platen Size 220 mm sq. Piston Stroke 215.00 mm Optional Fittings Digital Load indicator with RS 232 interface for connection to windows XP based computer system Digital Load indicator with printer interface Batteryback up for Digital Load indicator – in case of power failure Additional Pressure Gauge as `stand by` load indicator for emergency use in case of power failure Spare Oil seal Flexural test attachment (to be ordered at the time of purchase of machine.) Can be accommodated later on, only if request received at the time of placement of order Brick test attachment Block testing attachment Spacers to accommodate small size cubes and cylinders Hydraulic Oil Ram extracting tool

We are committed to provide precise analytical results by engaging advance testing machinery and equipments. A well-experienced and qualified technical manpower ensures perfect testing confirming to the international standards and norms. With a team of about half a dozen very senior, well qualified and highly experienced analytical employees and full fledged range of analytical instruments. Wet Chemistry lab facilities, At Accurate Metal Test Services we do cater to all your analytical requirements for Ferrous, Non Ferrous Metals, Minerals and Ferro Alloys.

As a dependable name, we make sure that our products are of excellent quality. To make it possible, we use only quality-approved and certified raw materials sourced from reliable vendors. As a trusted name in this arena, we also make sure that the offered products are meticulously packed using the premium material. In addition, our packaging experts check the lot prior to final dispatch.

  Specifications of the Basic Digital Tensile Testing Machine are as below:-1)   Tensile testing machine(Table Top Model) capacity upto      05 kgf to 0-250 kgf.2)   Imported guide rods for vibrationless travell3)   Linear Motion Bearing for friction less travell at high       speed.4)   Over Load safety5)   Over Travell Safety6)   Auto reverse function after complition of test7)   Auto stop function8)   PMDC Gear Motor & Drive for varible speed9)   Unit selection KG, N & KN10) Encoader for High accuracy in Elongation/ Extension11) 4 Line LCD Display Unit12) Last 5 samples readings will be saved in controller13) Single load cell & Double load cell both the facility  are available as per party’s requirement.

Reactive Dyes Testing Machine helps to determine the intensity of the color fastness. Reactive dyes are immensely used for the cotton fabrics plus it is an ideal for polyester, cotton, Rayon, Wool, Jute, Viscose, and Flax too. You can perform reactive dye testing for any type of fabric using Reactive Dyes Testing Machine. The significant advantage of reactive dyes is: it has good fastness aspects due to the bonding that takes place during fabric dyeing process. But sometimes due to improper reactive dye operation, pigmentation and other quality problems can be seen in the dyeing fabric which need to be tested as well as if you do not check the quality of the dyed fabric, it perhaps face color fastness due to external factors impact such as friction, washing, rain, sea water immersion, sunlight, etc. These all factors demand high quality color fastness aspect which not easy to fade. That you can evaluate by the testing the reactive dye fabric samples using Reactive Dyes Testing Machine.

The Aggregate impact value of coarse aggregate provides a relative measure of the resistance of an aggregate to sudden shock or impact. The oven dried and accuracy weighed aggregates are subjected to a total of 15 blows of specified weight and fall and percentage of fines formed in terms of the total weight of the sample is expressed as the aggregate impact value. The Apparatus consists of following:- A Testing Machine having a metal base with a painted lower surface of not less than 30cm in diameter. It is supported on level and plane concrete floor of minimum 45cm thickness. The machine have provisions for fixing its base. A Cylinderical cup of internal diameter of 102mm, depth 50mm and minimum thickness 6.3mm. A metal hammer or tup weighing 13.5 to 14 kg the lower end being cylindrical in shape, 50mm long, 100.0mm in diameter with a 2mm chamfer at the lower edge and case hardened. The hammer will slide freely between vertical guides and be concentric with the cup. Free fall of hammer will be within 380 + 5 mm A Cylinderical metal measure having internal diameter 75mm and depth 50mm for measuring aggregates. Tamping Rod 10mm in diameter and 230mm long, rounded at one end.

Living up to our reputation, we present you 5KN Testometric Universal Testing Machine. Enhanced with industrial expertise, we are a reputable figure in the industry. Our vendor management process makes certain that we procure from the vendors who can deliver the proposed quality consistently. It is equipped with features such as rigid construction, minimum maintenance and longer service life. We make the product available at market leading rates.            Description : The M350-5 range of twin column, computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface.   Features : Integral PC system running winTest™ Analysis universal testing software. Touch screen display with active tester control panel and readout screen showing real time test curves calculated results and statistics. Industry standard and / or customer specific test methods pre-installed. (Supplied separately with a CT model) Multi-lingual on screen keyboard. Self diagnostics software with on screen notification icons. Connection for remote monitoring of machines, with on-line service. Grade 0.5 load cells to all international standards including EN10002-2, EN7500-1, DIN51221, ASTME4, AFNOR A03-501, JISB7721. Grade 0.5 from 0.4% to 100%. Digital display of force, displacement, cell capacity, speed, position, mode, units etc. Real time graphic display with multiple axis selection, autoscaling etc. Manual control of crosshead with all functions. (Via touch screen on AT and PC on CT model) Configurable for cyclic and complex multi stage test procedures. Fully digital testing system with high precision control and accuracy, includes automated computer control of test methods. High resolution auto ranging load cells with accuracies better than +/-0.5% down to 1/1000th of the load cell capacity. Automatic recognition and calibration of load cells and extensometers, with instant calibration check facility. 800% overload capability of load cells without damage. Overload, overtravel and impact protection. Crosshead guidance system providing precise alignment and smooth running. Precision crosshead control via digital AC servo drive and brushless servo motor giving maintenance free operation and 4,000,000 steps per revolution positional control. High speed data collection systems for up to 4 synchronous channels. 6 I/O channels for additional devices such as extensometers, micrometers, callipers, balances etc. High stiffness loading frames with solid specialised steel crossheads and rigid extruded support columns with T-slots for accessory mounting. Software : Comprehensive winTest™ Analysis universal windows software covering tensile, compression, peel, shear, tear, cyclic, creep and multi stage testing. It includes a wide range of industry standard test methods and facility to create and store an unlimited number of further test methods. There is automated storage of all test data and ease of export to other software packages such as word, excel, access and SPC systems for enhanced report generation.

The "Surya" Hydrostatic Pressure Testing Machines are used to find out the resistence to internal pressure of R-PVC,C-PVC,U-PVC, MDPE, HDPE, LLDPE, Pipes, Fittings, Valves etc. as per IS, BS, ASTM and other equivalent standards. The "Surya" Pressure Testing Machines are designed keeping versatility in mind to perform with different applications as specified in international Standard. Surya's computerized model is suitable for many praecox applications of Gas pipes, Hosepipes and for the organisations with quality & quantity manufacturing base of above products.

Our team of expert professional to support and help to select best Hearing Aids according your life style. Now connect us our Sahara speech and hearing aids clinic.Essay our suggested hearing aids and listen to the difference.

Over the years, we have established ourselves as a prominent name in the industry in offering a wide range Hydrotester Machine. These products are manufactured by utilizing optimum quality materials incorporating advanced tools, technology. A fully automatic Hydro Testing Machine which requires minimal maintenance. All the operations are hydraulic and trouble free. 

DART IMPACT TESTING MACHINE is generally used to check impact strength of Plastic sheet and Films which are extensively used for packaging industries. Kant Plastology is serving this machine with robust construction and very operational ease mechanical fixtures. The offered apparatus determine the exact test result because of its perfect sample clamping attachment and friction free falling of Dart with dead weights release through magnet. The ease in operation and less maintenance are the key features of the machine.