Back Back
Exhaust Blower
Get Price Quote
5 Piece (MOQ)
Dust Collector Bag
Get Price Quote
10 Piece (MOQ)
Best Deals from Pollution Control Machines
Pulse Jet Dust Collector
185,000 Per Set
1 Set (MOQ)
Centrifugal Blower
Get Price Quote
Centrifugal fans and blowers typically have one of six types of wheels that draw the air into the inlet of the blower housing and discharges it at 90 degrees out through the discharge of the housing. Indair designs and manufactures centrifugal fans for wide range of pressure, direction of discharge and power to suit customer requirement. Many of the blowers in varying capacities are available in standard specifications. However, we specialize in offering one-off tailor made designs as well to suit customer specifications. The two most common types of centrifugal blowers are pressure blowers and volume blowers. Pressure blowers are designed to draw or push air at high pressures, generally rated in Pascal, Bar or SPWG (Static Pressure Water Gauge) in mm or inches. These blowers are used in burners, furnaces, glass cooling plants etc. Volume blowers are designed to draw or push larger volumes of air, generally rated in CFM (Cubic Feet per minute) or CMH (Cubic Meter per Hour). Centrifugal blowers are typically made of fabricated mild steel, stainless steel or cast aluminum, rarely in inconel, Cast iron and special steels too. Fans are manufactured with different impeller configuration as per application. If you have special requirements that cannot be met with standard fans or blowers, please contact us.
jet venturi fume scrubber
Get Price Quote
Jet Flow Jet Venturi Fume Scrubber is a dependable device designed to entrain and scrub large volumes of gases without the use of complicated baffles or moving Parts. The motivating fluid, generally water, leaves the nozzled in a hollow cone spray, creating a draft which draws the gases and vapores into the moving stream where they are continuously scrubbed / absorbed while subsequent separation is accomplished in units specifically designed bny, us to meet the state polution control requirement.
Fish Feed Dust Collector
Get Price Quote
Agricultural Waste Composting Machine
Get Price Quote
We are the leading manufacturers, exporters and supplier of this products.
Scrap Straightening Machine
190,000 - 200,000 Per Piece
1 PCS (MOQ)
Products Description ebar Scrap Straightening Machine is useful equipment for construction sites. This Scrap Bar Straightening Machine is useful equipment to straighten the scrap bars, to be put to use again. It also has a provision to out crocked ends of the her no that it can he put into the machine easily. Backed by latest technology support, these bar scrap straightening system help In delivering optimum performance support as desired by the customers. Straightens tangled and twisted steel bar such as scrap. Extremely effective for civil construction as straightened steel can be effectively put back to use. These scrap bar straightening machine mainly used in construction site and steel processing plant. Suitable for straightening hexagon bar, square bar, and Profiles brass bar convenience to change wheel easy and simple to adjust. Straightening machine is a metal bar, pipe, wire, and other equipment for straightening. Straightening roller straightening machine through the bars of pressure for them to change, such as straightness. There are two rows of straightening roller, the number of ranges. There is also two roller straightening machine, relying on Nu rollers (Concave Intermediate, hyperbolic roll) the perspective of the different changes in the diameter of the material straightening. Type of straightening of the main pressure, balance roller straightening machine, shoes roller straightening machine, anti-rotation bending leveierand so on. This process of straightening machine is: the location of the roller straightening products and the direction of the movement as a point of view, two or three of the initiative Is a pressure roller, driven by the motor for rotating in the same direction, on the other side of a number of A small roller was driven roller pressure, they are relying on a rotation of the rod or pipe so that the friction of the rotation. In order to achieve roller on the products required by the compression of this small roller at the same time or separately adjustments backwards or forward position, In general, the number of roller more after straightening products, the higher accuracy. Products have been biting into the roller, continue to make a straight line or rotary movement, making products to bear all aspects of compression, bending, u such as deformation, to reach the final straightening. Features : Smooth straightening & Auto cutting mechanism. Handy to operate and control the machine ensuring safety whilst in use. Hi- speed accurate straightening. The machine incorporates an overload value, which is designed to operate in case of overload. The machine runs on 3- phase power motor and is cost effective in power consumption Machine Helps in avoiding wastage of steel and encourages use of straightened smaller diameter bars in involved projects. Comes with hyperbolic straightening device that straightens bars without damaging ribs. Providers high work efficiency and safe operating environment. Avoid wastage of steel and re-use smaller dia. bars for your project needs Cutting Device to cut off extra lengths of bars Hyperbolic Straightening device straightens without damaging the ribs Easy to operation, low noise, low cost, high profit
Trommel Screen
80,000 - 550,000 Per Piece
01 Piece(s) (MOQ)
Introductions: MAGWELL Trommel screen is consist of five parts, such as drum, frame, hopper, reducer and motor. Working Principle: After the materials feeds into the drum, on the one hand, materials being screened along with the rotation of drum, on the other hand, the bigger materials flow forward along the direction of slope and be separated by the screen with different number of meshes. The different materials fall into different hopper and then sent to different finished product stacks by manpower or belt conveyor. Basic Parameters: Trommel screen type: sealed type, open type Construction of material: carbon steel, mild steel, stainless steel Drum type: round, hexagon Features: Screen replaceable for different mesh sizes Multiple screen size Easily changed screen plates Configured for economical & efficient classification, Screening and grading Heavy duty trommel drum with lifters at the front to facilitate material break up Largest processing capacity in the industry Unique screen design, result in higher capacities, longer screen life and no material clogging Heavy duty feed hopper and extension Gear drive mechanism Variable speed drive mechanism Application: Coal Industry: lump coal, coal dust, coal washing, etc. Gold Mine: gold screening and washing Chemical Industry: sifting calcium oxide, compost Metallurgy, construction, mineral- selecting, etc. Quarry: gravel, clay, mountain meal, sand, etc. Recycle Industry: Plastic ,MSW, E-waste, and etc Coir Industry
Hydrocyclone Separator
300,000 Per Piece
1 Piece (MOQ)
The Hydro cyclone separators and Partition fluid – solids twisters from the arrangement are intended for the expulsion of relative course solids from low consistency fluids.Working with nature, this progression in the process urges normally happening microbes to turn oxygen consuming. As these microorganisms expend waste, they release an innocuous gas that contains no smell.Our line of Hydro cyclone separators components channel pack, heartbeat plane channel sack and radial separators in soil can or container base arrangement. We have various models accessible for every sort of separator. We additionally highlight mix units that are stationary units with either a channel pack or heartbeat plane separator fusedIt is prescribed to incorporate a stream control valve in the arrival line to the procedure. This will permit representing of the move through the solids channel of the violent wind and the pioneers.The solids which will drop out of the vessel and can be gathered in a versatile compartment or waste transfer drum. The measurements of the strainers are relying upon the foreseen measures of solids and the limit of the principle procedure.
Air Pollution Control Dust Collector
Get Price Quote
Water Purifier Ozonator
200,000 Per Piece
1 Piece (MOQ)
Scrap Bar Straightening Machine
Get Price Quote
1 Piece (MOQ)
Bag Filter Venturi
Get Price Quote
Portable Dust Collector Machine
Get Price Quote
Air Pollution Control Equipment
Get Price Quote
For industrial applications, we are offering best quality of Air Pollution Control Equipment. The offered Air Pollution Control Equipment is extensively used as pollution control devices by industry or transportation devices. Moreover, the offer products are designed by our experience team using advance technology.
Air Compressor Parts
230 - 280 Per Unit
Air Compressor Parts A] Air Compressor- Spare Parts 1] INGERSOLL-RAND :- [ IR- T-30 / SS / NL / LPG Series ] 2] INGERSOLL-RAND :- [IR- ESV / ESH / IHE / PHE/ LLE / HSE / XLE- Series ] 3] ELGI Compressors : - [ ELGI- SC / TC / THPC / HV / SS / TS / HP Series ]Air Compressor Parts Aftercoolers Air Compressor Piston Rings Cylinder Gasket Filter Compressor Valves Compressor Parts Compressor Cylinder Air Compressor Spare Parts Pressure Gauges Unloader Piston Assembly Compressor Piston Cross Head Pin Compressor Piston Pins Connecting Rod Bush Pilot Valves Cylinder Head Repair
Scrubber System
Get Price Quote
We hold the expertise in manufacturing and supplying a wide assortment of scrubber system (FRP/PP). Ideal for those industries that depend on FRP, PP/FRP, these scrubbers help in eliminating the harmful gaseous pollutants and other contaminated particulates that arise due to the various industrial processes. These eco-friendly scrubbers are designed and manufactured following the high definition engineering principals keeping in mind the set industry standard. Specifications: Material: PP, FRP Maintenance: Easy Wet scrubber, Packed Bed columns, Absorption columns Chlorination column, Spray tower Venturi scrubbers
Industrial Dust Collector
Get Price Quote
Industrial Dust Collector is widely demanded in various industries in order to collect the dust particles. Our Industrial Dust Collector is recognized in the market for delivering high performance. Industrial Dust Collector features optimized ratio of air flow versus filter surface area. There is a possibility that the filter surface area will be utilized as central dust collection unit for multiple work stations. Clients can obtain bulk quantities of Industrial Dust Collector at market leading rates from us.
SINGLE STATION DUST COLLECTOR
40,000 - 70,000 Per Unit
1 Piece (MOQ)
concrete septic tank
60,000 - 120,000 Per one
bioscrubber
100,000 Per Piece
double inlet blowers
Get Price Quote
Non – over loading maximum airflow : 5,00,000 cmh maximum pressure : 350mm wgp size : upto 2.2m dia.
Wet Scrubbers
Get Price Quote
Goutham Equipments & Systems Offers custom designed Wet Scrubber for a variety of process conditions such as Chemical Reactions, Pickling, Plating, Chemical surface treatment, product recovery & others. Features: Design of system as per output conditions required Required Suction Hoods, plenums & ducting Blowers for air movement Recirculation Pumps & piping Process controls like pH, ORP, Temperature etc Other required accessories to complete the work on a turn-key basis Installation & commissioning at your site FRP with Vinyl, Bisphenols etc Engineering Plastics such as PP /PVC / CPVC / PVD
BIOMEDICAL LIQUID WASTE TREATMENT SYSTEM
240,000 - 500,000 Per piece
1 Piece (MOQ)
Biomedical Liquid Waste Treatment System uses a hybrid advanced electrocoagulation and electrooxidation cells for treatment of biomedical liquid waste generated from hospitals and clinical laboratories. The system is simple and easy to operate. The system does not use any chemicals for treatment. The treated effluent is safe for discharge into public sewerage. MODELS MODEL TREATMENT CAPACITY (L/DAY) RT ECO BML - 6 600 RT ECO BML - 12 1200 RT ECO BML - 24 2400 Ø For other Commercial models contact company directly RT ECO – Biomedical Liquid Waste Treatment System is hybrid electrochemical systems that are compact, eco-friendly and effectively eliminates biomedical pollutants and harmful pathogenic organisms such as bacteria and viruses. Hospitals, clinical laboratories and other biomedical liquid waste treatment facilities equipped with RT ECO – Biomedical Liquid Waste Treatment System for treatment of their effluent could meet the effluent discharge standards and regulations and also safeguard the environment from spreading of harmful diseases. Medical Waste-waters (Hospitals, Biomedical Labs, Blood bank liquid wastes) are contaminated with pathogens, such as bacteria, viruses, and parasites, human/nonhuman primate or other animal cells, diluted blood and tissue fluids, plasma, as well as hazardous chemical compounds, pharmaceutical compounds, and radioactive isotopes. Medical Industry, healthcare facilities equipped with RT ECO – Biomedical Liquid Waste Treatment System meets the standards and regulations, maintains effective water management and wastewater treatment solutions.
Wet Scrubber
130,000 - 1,050,000 Per Set
1 Set(s) (MOQ)
We are the manufacturer of Wet and Dry Type Scrubber for Pollution free Air. We Supply 99% efficiency.
air bag filter
125,000 - 150,000 Per Piece
Dry Air Scrubber
Get Price Quote
Ecocharm produces air scrubber that sucks contaminated air and free from air pollution, VOCs, surface contaminants, pet dander, odors and dust.
Marine Pollution Control Equipment
7,000 Per Piece
10 Piece7000 (MOQ)
Spares & Acessories
Food Waste Composting Machine
350,000 Per Piece
01 Piece (MOQ)
Filter by Localities
