Testing Equipment Dealers in Velachery, Chennai

The insulators testing device HVTS-HP is designed for testing the insulation of power cables and solid dielectric with the rectified voltage of up to 100 kV, as well as testing solid dielectrics with the sinusoidal voltage of up to 100 kV, 50 Hz. The main difference between series devices Cable test and diagnosis system HVTS-HP devices from Portable Hi pot Tester HVTS-7050 is the increased power output. There are two standard versions: 7.5 KVA and 17.5 KVA.

Meter measures Active Active, Reactive and Apparent energies in all four quadrants in forward and reverse directions, Instantaneous parameters phase wise voltages and currents,Power, Frequency, Rising Demand, Maximum Demand, Phase sequence, Power Factor, Date and Time. Eight Energy accumulators KWh, KVArh (lag and lead) and KVAh in forward and reverse directions, KWh and KVArh pulse output LEDs placed on front panel, LCD with backlight feature and LCD segments for indicating presence of voltages and currents in each phase separately is available, Front Key to stop and scroll to view display parameter, RTC with battery backup is used for time keeping and has a calendar of 100years, Data collection is possible through RS485 Communication with MODBUS RTU to PC and can also be done through Power Line Communication, Conforms to standards IS13779 and other relevant standards depending on the configuration.

from different points of production unit into a single Control Room source from where they can be extracted. Our Research, design, development and implementation methodologies adhere to and are compatible to all European and other International Standardization’s. Based on the customer’s requirements, conditions and needs, We source your implementation platforms from just across the best of the  industry. Dynamic plant visualization with easy operator interface. Customized reports and data logging options. Optional emailing periodic reports.

Comperessed Air Flow Meter, Dynoptic Dust Monitor, Ultrasonic Flow Mete

The most important parameters needed for water analysis, especially in drinking water, can be measured with Hanna’s HI93102 portable meter. This instrument not only measures turbidity, but also free and total chlorine, cyanuric acid, pH, iodine, bromine, and low range iron. Measurements are made quickly and accurately through a sophisticated, yet easy-to-use microprocessor. Users can select between pre-programmed calibration values or calibration points can be customized at a specified concentration or relative absorbance of the sample. The HI93102 offers many features that appeal to use in the field as well as in laboratory settings. The exclusive cuvette locking system ensures that the cuvette is inserted into the measurement cell in the same position every time to maintain a consistent path length. Up to 25 measured samples can be stored in memory, together with time and date. Miniaturization of the electronics has made it possible to o‰ffer unsurpassed accuracy and quality in a portable unit weighing just one pound.   Features at-a-glance AMCO AEPA-1 Primary Turbidity Standard - The AMCO AEPA-1 standards for the turbidity range of the HI93102 are recognized as a primary standard by the USEPA. These non-toxic standards are made of styrene divinylbenzene polymer spheres that are uniform in size and density. The standards are reusable and stable with a long shelf life. Logging – The HI93102 allows users to log up to 25 measurement readings. Measurement logs can easily be recalled with the press of a button and a reminder will appear if the memory becomes full. The logging mode can be enabled or disabled. GLP – With a press of the “GLP” button on the face of the meter, users can view the date, time, and two calibration values of the current mode. Auto-shut Off - Automatic shut off is selectable after 10, 20, 30, 40, 50, or 60 minutes of non-use when the meter is in measurement mode. This feature prevents wastage of batteries in the event the meter is accidentally left on. Battery Status Indicator -  The status of the battery is monitored during every measurement cycle. An indicator will warn the user when the amount of battery life left is not sufficient to take reliable measurements. Error Codes – Helpful diagnostic codes appear on the display alerting to problems including low light, high light, or sample out of range.

Multifunction Process multimeter source and measure Temperature functions , Thermocouples and RTDs Frequency, ohms, mV, Voltage, current , loop power Available PC interface with software Adopt ITS 90 Temperature Scale Used 5 digit LCD display with backlight Good accuracy 0.05 %, Battery Power operated RTC for Thermocouple Calibration 4X1.5 VDC Alkaline Battery for long life

Data Acquisition & Control solutions based on LabVIEW and National Instruments Hardware – We specialize in providing data acquisition and control solutions, including the complete chain of components starting from sensor till visualization and data processing based on NI LabVIEW customized to your requirements.

The MicroLite is an ideal solution for a variety of industrial cold chain logistics, requiring a small form factor USB data logger. Low cost, water resistant, multi-trip temperature data logger, with high resolution, 4-digit LCD display and direct USB connectivity – the MicroLite offers truly cost effective data logging. Accurate historical data indicator for an unbroken cold chain Six models offer a unit for every application Long battery life and 32K cyclic memory serve long haul transports Real-time LCD data display Dust and water resistant, depending on logger model License-free data analysis software The comprehensive MicroLite range allows organizations to select the unit most appropriate for their mission-critical environment:

Available with us are Rubber Hardness Tester that are high in performance and are easy to operate. Widely used across different industries, these rubber hardness tester are engineered to perfection adopting innovative technologies. We also endeavor to satisfy our clients spread worldwide by offering our range of rubber hardness tester as per the designs and specifications of our clients. Range:- 0 to 100 shore. Compact model and easy operate.

Battery Hydrometer Specific Gravity Tester- 6 / 12 / 24 / 48 vol

Tap Density Tester, Dissolution Testers, Tablet Disintegration, Teste

We are renowned as a reputed Exporter of an extensive gamut of Humidity Recorder, located in Tamil Nadu. It is made using high-grade raw material and modern machines by our vendors. Humidity Recorder is used for measuring the temperature and relative humidity in laboratories, storage, clean rooms, freezers, and other critical areas. Our Humidity Recorder is easy to use and operate.

Digital Meter, Diesel Level Monitor Meter, Emu Meat, Energy Drink

Breath Analyzer is used to investigate the alcohol content from the breath sample. Breath analyzer has advanced flat surfaced alcohol sensor, which has outstanding sensitivity and reproducibility, fashionable and portable design and it is more convenient for personal use.

Gauss Meter, Digital Gauss Meter, Electric Flux Mete