Testing Machines Dealers in Alandur, Chennai (17 products available)

Description Vibrating steel yard, no loose weight, clear graduations on Stainless Steel inclined index plate, main poise on steel rollers cannot travel beyond zero. Steel notch protects bar. Notches accurately cut by special machinery. Tumbler locking device Minor poise slides on a rigid brass index bar. The lever system enclosed in a strong cast iron frame is capable of withstanding loads for excess of rated capacity. The cast iron platform is mounted on ball bearing seated in beds on the stool to provide universal motion and avoid undue wear of the inter-changeable, hardened, steel knife edges & bearings which are easily replaceable when required.

Material : Mild Steel

Automatic Grade : Semi-Automatic

Phase : single

Power : 400-440v

Model Name/Number : VNSPL

Capacity : 100,200,400,600,1000,1200,1500,2000

Size : As per spec

Accuracy : AC supply

Place Of Origin : chennai

We Offer Fatique Testing Machine for repeated tensile load on wires can be performed in this machine.

The above machines are attached to a multi channel controller. The machine can be used in the stand alone mode by using the Controller. The movement of the cross head is achieved using a AC servo motor. The machines consist of a movable crosshead and a fixed cross head. The movement of the movable crosshead is aided by backlash free ball screws which help achieving high position accuracy and repeatability.

Features : Quality tested , Easy to use , Durable

Type : Spring Testing Machine

Application : Industrial

Grade : Automatic

Minimum Order Quantity : 1 Piece

depth : 9000m

pressure : 90 MPa (900 bar) max

Hyperbaric test facility is used to simulate the pressure in Deep-sea environment inside a high pressure vessel. The facility has been designed to test components with external pressure up to 90 MPa (900 bar) max., which is approximately equal to 9000m water depth. This facility is the first of its kind in India. Testing in this facility can save lot of time and money for qualifying underwater components, which otherwise would have been by actual testing in the sea at that depth.

Tensile strength is the stress at which a material breaks or permanently deforms. There are three definitions of tensile strength, yield strength, ultimate strength and breaking strength. Tensile tests are usually carded out on wire, strip or machined samples with either circular or rectangular cross section. Test pieces are screwed into or gripped in jaws and stretched by moving the grips apart at a constant rate while measuring the load and the grip separation. This data is plotted as load vs extension and then converted to engineering stress (load/original area) vs engineering strain (fractional change in length over the test section assuming the deformation is uniform). In special circumstances, the actual stress and strain may be calculated if the true cross section is measured during the test.   Features   Loading Accuracy as high as + 1% Straining at variable speeds to suit a wide range of materials. Continuous roll autographic recorder supplied as standard to enable study of the behavior of materials Motor driven threaded columns for quick effortless adjustment of lower cross-head-to facilitate rapid fixing of test specimen. High reading accuracy due to large size and design of dial. Wide range of standard and special accessories, including load stabilizer. Easy change from plain to threaded and screwed specimens. Large effective clearance between columns enables testing of standards specimens as well as structures. Simple controls for easy of operation. Robust staining frame of an extremely rigid construction. Safe operation ensured be means of safety devices. Fully enclosed and protected pendulum.  

Voltage : AC 220 V

Automation Grade : Automatic

Frequency : 50 Hz

Phase : Three phase

Vacuum Degree : 0 to -90 kPa

Accuracy : +/- 1% of reading force

Air Pressure : 0.7 MPa

Material : Stainless Steel

Automation Grade : Semi-Automatic

Surface Treatment : Galvanized

Working Temperature : -20 to 120 degree C

Tensile Strength : 200 - 400 Mpa

High pressure Leak Test : Upto 160 bar

Voltage : 110V, 220V, 230V, 380V, 440V

Automatic Grade : Automatic, Manual

Driven Type : Electric, Hydraulic

Type : Hydraulic Testing Machine

Certification : CE Certified, ISO 9001:2008

Color : Black, Brown, Grey, Light White

Condition : New, Used

Warranty : 1year, 2years, 5years

Testing asphalt pavement materials such as aggregate, reclaimed asphalt pavement (RAP) and mixture specimens often requires that samples be dried to a constant mass. Most labs accomplish this using convection ovens or fan drying, depending on sample type.