Milestone Instruments Uttam Nagar, Delhi

Two clamping systems 200 mm wide and 50 mm length in the direction of the applied force are mechanical wedge type and facilitate conducting Narrow Strip and Wide Width Tensile Strength tests as per many international specifications. These grips allow simple and rapid sample loading.

The apparatus is used in specification tests of masonry cement and physical testing of quicklime and hydrated lime. Unlike older models, the newly designed unit incorporates a vacuum regulator and gauge system in place of the old mercury manometer and relief column. The complete unit consists of an aspirator pump, vacuum regulator, vacuum gauge, three-way stopcock, flask, rubber gasket, brass funnel, perforated brass dish, filter paper and hardwood stand.

Vee-Bee Consistometer is determines the time required for transforming, by vibration, a concrete specimen in the shape of a conical frustum into a cylinder. Suitable for operation on 220 V, 1 phase, 50 Hz, AC Supply

Country of Origin : 220 V, 1 phase, 50 Hz

The Universal Testing Machine is designed to carry out various tests on Geotextiles viz. Narrow & wide Tensile Strength, Trapezoidal Tearing Strength, CBR Push through and Puncture Strength etc. The machine gives a choice of seven constant rates of travel of the lead screw ranging from a maximum of 320mm/min to a minimum of 50 mm/min. The capacity of the machine is 100kN (10000kgf).It is provided with two no of load cell 100 KN and 10 KN

The unit is Digital Microprocessor control and speed regulating by servo controlled motor and the speed can be from 5 mm to 500 mm. This frame also be use with CBR test on soil, Marshall stability test on Bitumen and many more tests where speed required is with in the limit and maximum load is below 100 KN.

This machine is for testing following test on the rubber. This is avilible from 50 kg to 500 kg. The cross head speed is 1 to 500 mm/min. Tensile Compression Flexural Peel Tear Friction Special Feature Interchangeable Load cells Self Identification of Load cells Load Measuring Accuracy of 0.5% Fully Digital Console with Large LCD Display & Key Pad. Auto Break Detection Stop / Auto Return Selection Wide Range of Accessories available

The unit is supplied complete with a stainless steel penetration test cone 35 mm long with a smooth polished surface and an angle of 30°. Facility exists for adjusting cone height in relation to the specimen. Cone Penetrometer consists of one each of the following : Penetration Test Cone Penetration Test Cup, 55 mm dia x 40 mm deep

It is a motor driven mechanical compactor useful for soil compaction. Two sets of Rammers are provided The rammer assembly is provided with a ratchet and pawl arrangement to lift it from the top of the soil layer. When the rammer reaches the required height the pawl release the rammer which falls freely on soil surface. An automatic blow counter fitted to the compactor is used to set the number of blows. The base plate of the specimen mould is to be fitted to the rotating base plate of the instrument which marks 1/5" revolution per stroke. The equipment is suitable for operation on 230 V, 50 Cycles, Single Phase, A.C. supply

Geotextiles can be cut or punctured during field installation, which can create a possible condition by which strength is controlled by a tearing resistance. An outline of an isosceles trapezoid is marked on a rectangular specimen (150 mm x 75 mm) cut for the determination of tearing strength, (with a 6 to 9 mm cut) and the nonparallel sides of the trapezoid marked on the specimen are clamped in parallel jaws of the Tensile Testing System.

This is a double lever (leverage 1:12) loading machine and the load is applied by flow of lead shots, which automatically stops when the sample breaks. The load is applied at rate of 450 to 550 N/minute ( 45 to 55 kg minute) or 2000 N/minute (200 Kg/minute) and the accuracy of load indication is ± 2%. The sample is mounted between rollers 40 mm dia or12 mm dia. Bearing Rollers can be placed at center distance of 150 mm, 200 mm, 250mm or 270mm as the case may be. Complete with 20 Kg lead shots.

The tile sample is pressed under a specified load against a grinding path, strewn evenly with an abrasive powder, revolving at the rate of 30 ± 1 rpm. At the end of 100 revolutions of the disc, the second parallel side of the tile is subjected to wear for an equal number of revolutions of the disc. The wear of the tile is measured using thickness-measuring device (which is supplied at extra cost). The abrasion-testing machine consists of a replaceable grinding path, fitted on to a disc rotating about its vertical axis. The rotating disc and the grinding path are enclosed by a circular tray. A bracket holds the specimen.

Availability : 7.5 kg

Thickness Gauge for geotextile This is used for measuring the thickness of the geotextile. The thickness of the geosynthetic material can be measured with an accuracy of 0.001 mm (depend on the dial gauge accuracy) for thickness up to 10 mm with Foot pressure of 6.35 mm, 10 mm and 56.4 mm diameter. Dead weight mechanism is provided to apply desired pressure varying from 2, 20 to 200 kPa. Surface plate is grounded and is rust free to enable reproducible results.

This is used for measuring the thickness of the geotextile. The thickness of the geosynthetic material can be measured with an accuracy of 0.001 mm (depend on the dial gauge accuracy) for thickness up to 10 mm with Foot pressure of 6.35 mm, 10 mm and 56.4 mm diameter. Dead weight mechanism is provided to apply desired pressure varying from 2, 20 to 200 kPa. Surface plate is grounded and is rust free to enable reproducible results. Specification Thickness measuring resolution 0.01 mm or as desired Thickness measuring range 0.01-12.5 mm or as desired

This is used for measuring the thickness of the geotextile. The thickness of the geosynthetic material can be measured with an accuracy of 0.001 mm (depend on the dial gauge accuracy) for thickness up to 10 mm with Foot pressure of 6.35 mm, 10 mm and 56.4 mm diameter. Dead weight mechanism is provided to apply desired pressure varying from 2, 20 to 200 kPa. Surface plate is grounded and is rust free to enable reproducible results.

Tensile testing machines are designed for determining the Tensile Strength and Elongation of a host of materials like ferrous and non ferrous materials, cables & conductors, Plastic, PVC, Rubber specimens, paper, plywood etc. Our tensile testing machines are also capable for conducting compression, Cross breaking and Shear tests thus making them more versatile with a few additional attachments. tensile testing machines are available in various capacities depending upon the requirements right from 5 kgf to 10 Tonnes ensuring ± 1% accuracy in test results.

These are used for testing the tensile strength and expansion of material like cables, wires, conductors, ferrous non- ferrous and packaging material. Further, by using relevant grips and combining correct transverse speeds, tests can be conducted on it and in addition, bending and compression tests can also be conducted on it. The machines are made in different capacities as per ISO, BS, DIN & ASTM standards. These are floor mounted and provide accurate data (accuracy within 1 +) on the physical properties of materials in a very quick and simple manner.

Steel, and 16 mm dia x 600 mm length rounded at the lower end for use with Cube and Cylinder

Using a speedy moisture meter, the moisture content of soils, sand and other fine-grained material can be obtained quickly with reasonable accuracy. The test technique is based on the fact that water will react with calcium carbide to form acetylene gas and the quantity of gas formed is directly proportional to the water present, leaving a surplus of the chemical used in the test. The quantity of acetylene gas produced is indicated on a built-in pressure gauge, which is calibrated in percentage of moisture on wet weight basis.   Speedy Moisture Meter Range: 0 - 25%, Accuracy Division: 1% Speedy Moisture Meter Range: 0 - 50%, Accuracy Division: 1%

Compaction : Soil compaction is a fundamental requirement for the construction of earth fill for dams, reservoirs, canal embankments, highways, railways and runways. The relationship between soil moisture content and compacted dry density is very useful for deciding construction specifications and quality control of compacted earth fill. While designing an earth or earth retaining structure, the strength and deformation behaviour of soil is evaluated by testing soil specimen compacted to the density as would be achieved during construction. The construction quality control is essentially to check the density of compacted soil achieved in the field, thereby checking its strength.

This apparatus used for determining the slump of fresh concrete as a measure of its consistency. It consists of a pressure-tight flanged cylindrical measuring bowl, fitted with a removable flanged and a conical cover assembly with a seal in-between. The conical cover has an air valve and a petcock for bleeding off the water. A cylindrical standpipe, which is graduated in percent air content, is fixed to the conical cover assembly. Required pressure is applied to the specimen with the help of a pressure bulb. The recommended limits specified for the air content are between 3% and 6.5%.Each apparatus is supplied complete with a calibrating cylinder, pressure gauge, funnel, trowel and tamping bar.

The apparatus consists of a motor on baseboard capable of driving two or four drums at a speed of 20 rpm. A suitable number of plastic water troughs, each designed to contain a test drum with quick release drive assemblies, permit 1 to 4 drums to be driven at one time. The test drums are supported on water lubricated bearings allowing 40 mm unobstructed clearances below the drum and a trough water level 20 mm below the axis of the drum. Drums are made of brass and comprise 2 mm wire mesh cylinders of 140 mm dia and 100 mm length.

Sieve Shaker Table top type To make the process of sieving easier and quicker, electrically operated mechanical table top type sieve shakers are offered for dry sieving. These Sieve Shakers are popularly used not only in soil laboratories but also dry sieving the geotextile testing

ELECTROMAGNETIC SIEVE SHAKER, which have been developed applying the latest technological advances of power control. The sieve shakers microcontroller is used to set both the process time from 1 min to 99 min and the amplitude from 0.5 to 3.5.

To make the process of sieving easier and quicker, electrically operated mechanical Sieve Shakers are offered for dry sieving. These Sieve Shakers are popularly used not only in soil laboratories but also in a number of industries where sieving is required; such as for ores, refractory materials, minor aggregates, pigments, powdered coal, soap, cement, roofing materials, plastic moulding powders and pharmaceuticals. The Sieve Shaker can carry up to 7 sieves. Sieve Shaker Manual. Hand Operated Sieve Shaker motorised Gyratory for 200mm sieves It is driven by a ¼ HP motor. The Sieve Table is inclined from the vertical axis and the direction of Inclination changes progressively in the clockwise direction. In addition to the gyratory motion of the table, there is a tapping motion as well.

Water supply system is designed to spray the water on the sample it is provided with the flow control valve on the front and with two indicator one for power supply on and one for pump on.