Epoxy Adhesive
Get Price Quote
Panther Diamond Synthetic Resin Adhesive
90 Per kgs
50 Barrel (MOQ)
Best Deals from Dextrin
Insulation Adhesive For Transformer
Get Price Quote
INSULATING ADHESIVE TA-4000: The product is a room temperature curing insulating adhesive. It is used in the manufacturing and repair of paper covered conductors. It is also used in the construction of oil filled Power & Distribution Transformers. The ‘Target’ made INSULATING ADHESIVE TA-4000 is most preferable product in the Transformer industry up to 1.6KV with quick curing time and best insulation. Area of Application: For Copper-Aluminum coil winding with insulation paper. For sticking press board to make block/duct to avoid slip. For cotton tape wrapping on LV-HV coil covered with insulating paper. ADVANTAGES: It is solvent free and safe. Room temperature curing. Fully cured bond is resistant to transformer oil & chlorinated di-phenyl. Manufactured from eco-friendly chemicals.
Silicate Adhesive
Get Price Quote
We are noted Manufacturer and Supplier of Silicate Adhesive in the domestic market. We have wide variety of Silicate Adhesive that is used for lamination of Copper to Walls, Plywood to Steel or soft metals. We also offer tailor-made Liquid Silicate Adhesives for bonding Aluminu Foil to Paper. Setting speed, viscosity, bonding strength etc., are few parameters on which we can customize our Silicate Adhesive.
Cyanoacrylate Adhesive
Get Price Quote
Natural Rubber Latex Adhesives
80 - 135 Per Ltrs
Different Grades in Natural Rubber Latex Adhesives Natural Rubber Latex adhesive is a water-based adhesive made primarily from natural rubber latex. It is a milky-white water based viscoelastic liquid is using for adhering two substrates is known as LATEX ADHESIVE that can be used to bond a wide range of materials. Generally adhesive can be divided in to two main categories “TEMPORRARY ADHESIVES” and “PERMANENT ADHESIVES”.Classification of adhesive is based on the end use and joint strength between the substrates. UNITEXX FW NL SERIES is under the category of TEMPORRARY ADHESIVES. UNITEXX FW NL SERIES ADHESIVES are manufacturing from pure natural centrifuged rubber latex, incorporating with chemicals are derived from petrochemical origins showing the characteristic properties for the end use.
wall tile adhesives
160 Per Bag
Virsun classic Floor Tile Adhesive is bis apoved isi standard is 15477:2019 type 1standrd en 1348 a bagged cementitious powder to be mixed with water for installing ceramic the and natural stone using the thin-set method of Installation. Tile adhesives are a factory prepared blend of carefully selected raw materials. Portland cement and graded aggregates (Latex) are added to adhesive powders to increase bond strength. Best suited for Exterior and Interior Installation of ceramic/ vitrified/ Porcelain/Engineered stones and Natural Stones. ApplicationsBest suited for Exterior and Interior installation of ceramic/ vitrified/ Porcelain /Engineered stones and Natural Stones.AdvantagesSingle component, ready to useProven performanceHigh strength formula & ultimate flexibilityIdeal for external facades and underwater applicationSuitable SubstratesCernen1 Mortar BedCement PlasterBrick MasonryCernentTerrazzoFeaturesSingle component, ready to useProven performance.
Orifix Blocks Adhesive
500 Per Kilogram
40 Kilogram (MOQ)
Heat Resistant Hot Melt Adhesive
400 Per Kilogram
100 Kilogram (MOQ)
Polyfix Instant Cyanoacrylate Adhesive
Get Price Quote
100 Piece (MOQ)
NSA-S-125 Tile Adhesive
Get Price Quote
500 Pack (MOQ)
Medium Cure Thermally Conductive Adhesive (8329TCM)
Get Price Quote
We are a well-reputed Supplier of Medium Cure Thermally Conductive Adhesive (8329TCM) in Maharashtra, India. The 8329TCM Medium Cure Thermal Conductive Adhesive is an electronically insulating epoxy that combines moderate curing rate and high-thermal conductivity. It has a convenient 1-to-1 ratio, a workable 45 minutes pot life, and a moderate curing rate. It may achieve a minimal service cure in seven hours at room temperature. The cured adhesive bonds very well to most substrates used in electronic assemblies. It resists thermal and mechanical shocks. Features : Excellent 1.36 W/ (m¢K) thermal conductivity Easy 1:1 mix ratio Adheres to most electronic substrates Stores and ships at slightly below room temperature no freezing or dry ice required Very long shelf life of at least two years even when stored at room temperature Strong water and chemical resistance to brine, acids, bases, and aliphatic hydrocarbons Applications : The 8329TCM is used for thermal management situations requiring superior bonding strengths and good thermal transfers. For example, it is used to as a die-attach for electrical and electronics, increasing their long-term reliability. It is great for heat sink bonding. It is also used as a high-powered LED adhesive that maximizes the lifetime of LEDs by dissipating their heat. Application Instructions : Follow the procedure below for best results. For mixing quantities that are less than 1 mL in size or for stricter stoichiometry control, mix by weight ratio instead (requires a high precision balance). Heat cure is recommended to get the best possible conductivity. To prepare 1:1 (A:B) Mixture : Remove cap or cover. Measure one part by volume of A. Measure one part by volume of B. Thoroughly mix the parts together with a stir stick until homogeneous. Apply with an appropriate sized stick for the application area. Note : Remember to recap the syringe or container promptly after use. Tip: Note that the material viscosity decreases with mixing, so the material will be most liquid-like and easily applied immediately after being mixed. Due to short cure time, apply as soon as possible after mixing. To heat cure the 8329TCF Put in oven at 65oC [149oF] for 15 minutes. Tip - Hair dryers are normally rated not to exceed 60oC, so they can generally be used to accelerate the cure. Attention - Keep the curing temperature well below temperature limit of heat sensitive components that may be present. As a guideline, remember that commercial grade devices normally can be safely operated up to 70oC, industrial grade up to 85oC, and military grade up to 175oC. Attention - Heat guns can easily exceed the temperature limits for your assembly: they should not be used.
Fevikwik 203 Cyanoacrylate Adhesive
Get Price Quote
10 Piece (MOQ)
Mycron Synthetic Lamination Adhesive
105 - 145 Per Kilogram
1000 Kilogram (MOQ)
We are the major supplier's of this product for Packaging and Lamination.
Amcrylate Tissue Bio-Adhesive
Get Price Quote
100 Piece (MOQ)
Product Introduction : Amcrylate Bio-Adhesive is used for closure of surgical incisions. It is available as bio-adhesive reduces the risk of post surgical infection and trauma. It does not leave any scar and has cosmetic look. Uses of Amcrylate Bio-Adhesive : Closure of surgical incisions
Water Proofing Adhesive
825 - 1,100 Per liter
20 Kilogram (MOQ)
Neosol Aa - (700) Synthetic Rubber Based Adhesive
Get Price Quote
Neosol Aa – 700 is a Synthetic Rubber Based Adhesive in Solvent Solution with Over 18 % - 20 Solid Content. It is Light Brown in Color and is Most Suitable for Foam to Foam, Rexine with Foam, Foam with Coir & Spring, Dg Canopy, Sports Goods, Footwear and Many other Applications. pack Sizes 20 Ltr, 5 Ltr, 1 Ltr, ½ Ltr & 200 Ml. Please Contact Us.
Home Pride Tile Bonder
Get Price Quote
Home Pride Tile Bonder is Single Component when mixed with Cement it gives ultimate Strength for fixing tile on wall & floor recommended for interior & exterior use.
Keralastic T Polyurethane Adhesive
3,481 Per Pack
EVOBOND 502 20GM Cyanoacrylate Adhesive
Get Price Quote
500 Carton (MOQ)
Product Name : HIGH PERFORMANCE SERIES CYANOACRYLATE Product Description EVOBOND High Performance Series Cyanoacrylate Adhesive is instant bonding single component adhesive that bonds almost all close-fitting smooth surfaces in seconds. It requires no mixing,no heating, and no clamping. Containing no solvent, the adhesive is mild in odor, low toxic ,and low flammable. Different types of viscosities are available for different applications. Low viscosity product features good penetration for fitting smooth surfaces, while high viscosity product provides outstanding adhesion for porous surfaces.THIXOTROPIC GEL is especially for vertical and porous surface application,which will not migrate and can be cured better with EVOBOND ACTIVATOR. MEDIUM SETTING VELOCITY & HIGH STRENGTH Applications : Metal, plastic, rubber, especially for metal. GradeChemicalTypeViscosity(CPS)Gap Fill(mm)Setting Velocity(Sec.)Shelf life(Month)Tensile-Shear Strength(kgf/cm2) W-50 ETHYL 2-3 0.04 10 12 120 ~ 200
Rapid FIX IT Instant Adhesive
23 - 25 Per piece
100 Piece (MOQ)
Aerobond 555 Pasting Adhesive
200 Per Kilogram
100 Kilogram (MOQ)
floor tile adhesive
Get Price Quote
Hot Melt Glue Adhesive
345 - 545 Per piece
1 glue (MOQ)
Quality Spine Glue Adhesive(Transparent) Used Perfect Binding Machine Grade A1 User/Application Personal & Personal Use, Padding (Book, Register, Diary, Catalogue) Packing Quantity 1 kg Per Package Type Bits(Chips) Machine Compatibility With all types of glue binding machine Colour White & Yellow Odor Very low
Kleiberit 773.3 Adhesive
Get Price Quote
100 Pack (MOQ)
MBEPOXY Violet Epoxy Adhesive
600 Per Kilogram
Floor & Wall Tile Adhesive
Get Price Quote
RECOMMENDED FOR TILE ON TILE APPLICATION IDEAL FOR FIXING CERAMIC & VITRIFIED FLOOR & WALL TILE THIN LAYER SETTING POLYMER BASED ADHESIVE Based on German Technology
Corrugated Board Adhesive (CORRUGLUE 300)
45 - 48 Per Kilogram
1000 Kilograms (MOQ)
Described as a Starch based corrugated board adhesive with cold water ratio 1:3, the Corrugated Board Adhesive (CORRUGLUE 300) that we offer is a preferred choice for high speed corrugated auto plant. Applications: 3, 5, 7 ply High speed corrugated Auto plant
filter adhesive
Get Price Quote
Homesure W Shield Super Bonding Repair
Get Price Quote
100 Litre (MOQ)