Back Back
Bourns 3296 Trimmer Potentiometer
6 Per Piece
Electronic Resistors
Get Price Quote
We offer a wide range of Electronic Resistors for our customers. The Electronic Resistors are known for their superior resistance and dissipated power. Our customers use the Electronic Resistors range for various applications for restricting the flow of electric current. The resistors are appreciated for their unique features such as temperature coefficient, noise free operations and inductance. Available In Range Of : ¼ W to 5000 W upto 12 KV 1Ω to 10 GΩ. Various Types Of Resistors Offered By Us Include : Carbon FilmMetal FilmMetal OxideVDR / MOVPTC / NTCWire WoundNon-inductiveHigh VoltageVariablePotentiometer Available In The Following Makes : SUREMFRCeraohmsPankajElproDuratechVCRSupertronPhilips
Best Deals from RF Passive Components
Multilayer Ceramic Capacitor
1 Per Piece
1000 Piece (MOQ)
Single Tube Rheostat
Get Price Quote
rheostat, single tube a layer of oxidised resistance wire is wound on a porcelain tube which is supported by end supports. A sliding contact and three 4 mm socket terminals are provided for use as a rheostat or as a potentiometer. Tube diameter 38 mm simple voltaic cell daniel cell lechlanche cell in plastic vessel demonstration electric bell telegraph set, vertical type telephone set, lecture pattern worcester circuit board westminster electromagnetic kit power supply, 2v demonstration transformer demonstration dynamo model induction coil, ruhmkorff wheatstone bridge potentiometer rheostat, single tube rheostat, projected resistance coil resistance unit resistance box, plug pattern post office box, wheatstone bridge
Dry Type Ac & Dc Low Tension Power Transformer
Get Price Quote
1 Piece (MOQ)
Photo Resistor for Oil Flames
Get Price Quote
The Photo Resistor for Oil Flames is designed to detect visible light emitted by oil flames. These are not suitable for oil fired furnaces with refractory glow. The resistor is designed and manufactured in compliance with set industrial standards using qualitative material. Designed to detect visible light emitted by Oil flames. Front and Side view models Not suitable for oil fired Furnaces with refractory glow.
Discreet and Passive Components
Get Price Quote
We at KMS Technologies hold expertise in offering a comprehensive range of discrete and passive componentsfor the clients. Being a leading discrete and passive components distributor in Mumbai, our entire range is in conformation with international standards & norms. These offered products are in huge demand in various electronic industries. We are the best discrete and passive components sourcing agents in order to fulfill the specific requirements of our clients and sourced from reputed vendors and manufacturers of these products. Apart from this, the offered range is, durable in nature, easy to install and have longer serving life. With the help of our top-notch transit facilities, we at KMS Technologies are capable to deliver the consignments in the stipulated time frame. Feel free to get in touch with us for these discrete and passive components.
Industrial power capacitor
700 Per Piece
10 Piece (MOQ)
thin film rtd elements
Get Price Quote
1 Piece (MOQ)
Alba Sensors' Thin film Platinum based elements offer Class A outputs using the most cutting-edge high-tech techniques, including laser spray plating, microphotography, and printing lithography. The resistance value is adjusted via digital trimming, which results in the highest level of accuracy.VersionsPT50, PT100, PT500, PT1000, PT2000, CU50 & more.Technical description Temperature coefficient R100/R0=1.3851. After strictly picking up and indicating the exact value of each element at 0 centigrade. Film Pt thermal resistance element with ceramic and platinum specially made to maintain excellent stability under high temperature, suitable for use in the -70 C ~ 6OO temperature. The platinum film is spatter on the surface of the ceramic by laser, thus the thin film platinum thermistor element has good anti vibration and anti shock properties. The surface of the film is covered with ceramics, so the element can withstand high voltage and has good insulation.
High Voltage Capacitors
Get Price Quote
Our company specializes in exporting and supplying precision engineered High Voltage Capacitors. Specifically designed to be the part of different types of measuring equipment, the High Voltage Capacitors are known for their supreme quality, high reliability and elevated durability. High Voltage Capacitors find wide application in power industries, which include high-voltage labs, industrial plants, and power substations.Models available : IHCs-10 IHCs-35 IHCs-110 IHCs-220 IHCs-330 Application : Electrical testing of various products meant for industrial applications (e.g. HV insulation tests including transformer oil) Providing traceability of measurements (calibration of instrument capacitors, voltage transformers and voltage dividers of 0.2 – 0.5 accuracy classes or less accurate).
DC Shunts
Get Price Quote
We stand in the midst of leading Direct Current Shunts Manufacturers, based in India. ME Dc Shunts are available for current ratings from 5-10000 Amps and mill volt drops of 75 milli volts. (Other voltage drops can be provided at request) The Shunts confirms to IS Standards 1248 ME Dc Ammeter Shunts consist of Mangenin rods soldered or silver brazed to brass end blocks. The shunts are artificially aged after manufacture and then tested on full load. Shunts are supplied with leads of 0.025 ohms. The lead resistance is taken into account while calibrating the shunt. Overload: Shunts are capable of withstanding temperatures upto 120 C without any permanent alterations in physical or electrical properties. Overloads and faults which results in temperatures of this magnitude can be safely handled All 75 milli volts drop shunts of class 1, withstand the following overload Requirements : 2 X rated current for 3 minutes. 4 X rated current for 30 seconds. 10 X rated current for 5 seconds. Temperature Co - Effecient : 0.002% per degree centigrade, above ambient temperature in still air, with free ventilation. Temperature not exceeding 120°C at the center and 90°C at the ends.
uv choke
145 Per Piece
Rf Modules
Get Price Quote
Buyers can contact us all year round for purchasing reliable RF Modules at market leading prices. Due to our exceptional and completely secured payment procedures, we have successfully gained full customer satisfaction. We make available varied payment procedures to ensure smooth transactions. The offered RF Modules are widely utilized in smart-phone accessories, wireless microphone, PC and tablet peripherals etc.
electronic inductor
200 - 500 Per Piece
500 Piece (MOQ)
Toroidal inductors and transformers are electronic components, typically consisting of a circular ring-shaped magnetic core of iron powder, ferrite, or other material around which wire is coiled to make an inductor. Toroidal coils are used in a broad range of applications, such as high-frequency coils and transformers.Toroidal inductors can have higher Q factors and higher inductance than similarly constructed solenoid coils. This is due largely to the smaller number of turns required when the core provides a closed magnetic path. The magnetic flux in a high permeability toroid is largely confined to the core; the confinement reduces the energy that can be absorbed by nearby objects, so toroidal cores offer some self-shielding.Common Mode Chokes Common Mode Chokes are used when many electrical devices may be connected to the same power lines (or power supply lines) and therefore substantial electrical noise can exist on these lines. Line filters prevent excessive noise from being conducted between electronic equipment and the AC line. Noise is typically common to both lines and in the same direction. Common mode chokes are designed so that common mode current creates a magnetic flux (through mutual inductance) that adds to attenuate the CM noise signal. The normal (differential) mode currents create magnetic flux that ideally cancel each other out so the normal signal frequencies are not attenuated. Any inductance encountered by the differential signal is the result of imperfect coupling of the two coils. Design requirements for a common mode choke It is typical for the inductance value of a common mode choke to be specified as a minimum requirement, thus insuring the crossover frequency is not shifted too high. The frequency range of the interfering signal should be given to allow proper calculation of the attenuation of unwanted signal noise in the design. Proper wire sizing is accomplished by specifying the voltage and current levels across and passing through the common mode choke. Toroid InductorsToroid style common mode chokes are designed to provide the highest common mode impedance over the widest frequency range. These parts are ideal for any application requiring a high DC current bias and are well suited for use in switch-mode power supplies. Common mode chokes are most effective in filtering supply and return conductors with in-phase signals of equal amplitude. Differential mode inductors are available for filtering out-of-phase or uneven amplitude signals.A Toroidal inductor is an inductor that is designed on a doughnut shaped core. Toroidal inductors offer small size, less leakage inductance and lower electromagnetic interference (EMI).Design requirements for a Toroidal Inductors:Typical minimum requirements to be specified for a Toroidal inductor design are: No load inductance in uH Full load inductance in u HDC Current in Amperes AC Current in Amperes peak to peak Operating frequency is needed for core calculations and wire sizing Core material is selected for the known operating frequency or frequencies. Other Toroidal inductor design considerations are space limitations and mounting technique. Lead terminations are also specified through the design of a Toroidal inductor. Pulse TransformerA pulse transformer is a transformer that is optimized for transmitting rectangular electrical pulses--that is, pulses with fast rise and fall times and a relatively constant amplitude.Principle 8 Operating Principles Magnetizing (No-Load) Current Voltage Drop Voltage-Time Product Kickback Voltage Secondary Load Current Effects of Winding Capacitance The Trailing Edge Pulse Distortion The magnetic flux in a typical A.C. transformer core alternates between positive and negative values. The magnetic flux in the typical pulse transformer does not. The typical pulse transformer operates in an “unipolar” mode (flux density may meet but does not cross zero.) Pulse transformer designs vary widely in terms of power rating, inductance, voltage level (low to high), operating frequency, size, impedance, bandwidth (frequency response), winding capacitance, and other parameters. Designers try to minimize parasitic elements such as leakage inductance and winding capacitance by using winding configurations which optimize the coupling between the windings.
Industrial power capacitor
Get Price Quote
Aluminium Housed Power Resistors
Get Price Quote
trim pots
Get Price Quote
Neutral Grounding Resistors
25,000 - 500,000 Per Piece
1 Piece (MOQ)
ultra capacitors
Get Price Quote
Our organization offering best Ultra Capacitors supplier.
High Current Low Voltage Load Resistor
Get Price Quote
We provide excellent quality Water Cooled High Current Low Voltage Load Resistor that operate with direct cooling without Heatsink and better Power / Volume ratio, 90% Heat dissipation in water.
Neutral Grounding Reactors
Get Price Quote
Neutral Grounding Reactors (NGRs) are used to control single line to ground faults only. NGR are particularly used at transmission voltage levels, when autotransformers with a delta tertiary are employed. Neutral Grounding Reactors (NGRs), normally installed between the transformer or generator neutral and ground, are effective in controlling single line to ground faults since, in general, the system short circuit impedance is largely reactive. NGRs reduce short circuit stresses on station transformers the most prevalent type of fault in an electrical system.
Capacitor
Get Price Quote
A capacitor (originally known as a condenser) is a passive two-terminal electrical component used to store energy electrostatically in an electric field. The forms of practical capacitors vary widely, but all contain at least two electrical conductors (plates) separated by a dielectric (i.e., insulator). The conductors can be thin films of metal, aluminum foil or disks, etc. The 'nonconducting' dielectric acts to increase the capacitor's charge capacity. A dielectric can be glass, ceramic, plastic film, air, paper, mica, etc. Capacitors are widely used as parts of electrical circuits in many common electrical devices. Unlike a resistor, a capacitor does not dissipate energy. Instead, a capacitor stores energy in the form of an electrostatic field between its plates. It includes all kinds of capacitors (Ac & Dc) for multi use.
Wire Wound Resistors
6 Per Piece
Silicone Coated Axial Wire Wound Resistors
6 - 7 Per Pieces
1000 Piece (MOQ)
High Voltage Divider
Get Price Quote
Dry Filled Power Capacitor
100 Per Piece
variable resistors
Get Price Quote
snap in capacitors
Get Price Quote
Product Details: Capacitance 1- 22000 MFD Voltage Rating 16-450 V
Electronic Capacitors
Get Price Quote
We are engaged in supplying electronic capacitors of superior quality. The electronic capacitors provided by us has excellent finish, compact design, and smooth surface. We provide these electronic capacitors to our clients in excellent packaging.
Electrolytic Capacitors
Get Price Quote
100 Piece(s) (MOQ)
we are offering electrolytic capacitors. an electrolytic capacitor is a type of capacitor that uses an electrolyte, an ionic conducting liquid, as one of its plates, to achieve a larger capacitance per unit volume than other types. they are often referred to in electronics usage simply as "electrolytic”. they are used in relatively high-current and low-frequency electrical circuits, particularly in power supply filters, where they store charge needed to moderate output voltage and current fluctuations in rectifier output. they are also widely used as coupling capacitors in circuits where ac should be conducted but dc should not. there are two types of electrolytic: aluminum and tantalum. electrolytic capacitors are capable of providing the highest capacitance values of any type of capacitor (see super capacitors) but they have drawbacks which limit their use. the standard design requires that the applied voltage must be polarized; one specified terminal must always have positive potential with respect to the other. therefore they cannot be used with ac signals without a dc polarizing bias. however there are special non-polarized electrolytic capacitors for ac use which do not require a dc bias. electrolytic capacitors also have relatively low breakdown voltage, higher leakage current and inductance, poorer tolerances and temperature range, and shorter lifetimes compared to other types of capacitors.
Filter by Localities
