Calibrators Dealers in Navi Mumbai

INTRODUCTION The SIKA UC mAV is a hand-held process calibrator (conforming toEC standards). It is more particularly intended for calibration and maintenance. It can measure and generate electrical quantities either on siteor in the laboratory. It fulfils voltage and current measuring and generation functions (DC or LF rampsignals) and a continuity test (on passive loop). Owing to its monitoring (regulation) mechanism in transmission mode, the instrument cannot take measurements and transmit simultaneously. APPLICATION Display of results in accordance with a linear conversion law or not. Generation of increments, single or cyclic ramp signals. Its utilisation is facilitated by a series of improvements Fast access to all the functions. Intuitive user interface. Graphic display of 160x160 pixels Connection by 4-mm safety sockets. Powered by 4 AA batteries or a rechargeable battery pack with fast internal charger (Option). The instrument is enclosed in an ABS casing with an elastomer sheath. CHARACTERISTICS Hand-held instrument energized by 4 AA batteries (1.7 Ah Ni-MH battery pack on option). Wrist-strap for carrying and use on sites Graphic 160 x 160 pixel liquid crystal display (LCD). Choice of language of the messages and programming functions, ranges and parameters on 6-key keypad + 1 navigator. Display backlighting accessible via the keypad, with the possibility of programming automatic extinction after a given period of inactivity. Presentation: ABS casing (elastomer sheath on option). Dimensions: 157 mm x 85 mm x 45 mm (without sheath). Weight: 306 g without sheath. Sealing IP54 in accordance with standard EN 60529 UC mAV is compatible with HART transmitters by inserting a 250 resistance which doesn't disturb digital data transfer.

Radix Calibrators offer several functions. Operating in measuresource mode, these instruments can handle RTD, mA, mV, thermocouple (TC) and ohms signals amongst others. They can also simulate a 4-20 mA and 24 V loop supply to calibrate other instruments. MICROCAL is lightweight and cost-efficient and RADICAL is a full-featureed cailbrator. Both are microcontroller based, incorporating a highly stable reference and automatic error correction.

UT Calibration Blocks or ultrasonic calibration blocks are widely used in the calibration process. These UT Calibration Blocks are made using ultrasonically tested materials and appreciated for attributes like sturdy construction, corrosion resistance, excellent finish, etc. We provide UT Calibration Blocks in different sizes and in secured wooden box.

Fully automatic calibration accomplished by a smooth noiseless motor driven standard weight inside the balance eliminating weight maintenance. Accurately machined stainless steel standard weight is used for the purpose. Any tolerance in the weight machining is corrected through software. Balance can be programmed to initiate the motorized calibration process every time when it is switched ON, change in the ambient temperature, at a preset time to recalibrate the balance.

Fully automatic calibration accomplished by a smooth noiseless motor driven standard weight inside the balance eliminating weight maintenance. Accurately machined stainless steel standard weight is used for the purpose. Any tolerance in the weight machining is corrected through software. Balance can be programmed to initiate the motorized calibration process every time when it is switched ON, change in the ambient temperature, at a preset time to recalibrate the balance.

Fully automatic calibration accomplished by a smooth noiseless motor driven standard weight inside the balance eliminating weight maintenance. Accurately machined stainless steel standard weight is used for the purpose. Any tolerance in the weight machining is corrected through software. Balance can be programmed to initiate the motorized calibration process everytime when it is switched ON, change in the ambient temperature, at a preset time to recalibrate the balance.

Fully automatic calibration accomplished by a smooth noiseless motor driven standard weight inside the balance eliminating weight maintenance. Accurately machined stainless steel standard weight is used for the purpose. Any tolerance in the weight machining is corrected through software. Balance can be programmed to initiate the motorized calibration process every time when it is switched ON, change in the ambient temperature, at a preset time to recalibrate the balance.  

SIXSENSE Offers mV / mA calibrator for calibrating any type of thermocouple / mA inputs . Product is suitable for each and every Process industry like steel , plastic, jewellery , pharma etc . Product is very handy and tested for mA load also. It is operated on 9V (2 Nos) battery . Fuse protection protects for any accidental occuring.

Sound Level Calibrator, Proximity Control Unit, Instrument Stand

Calibrators, RTD Sensors, Pressure Gauges, Dial Thermometer Gas Fille

Calibrators, Temperature Scanners, RPM Indicator, Loop Powered Indicator

Acoustic Calibrator, Media Preparator, Portable Indoor Air Quality CO2 Mete

3 Phase Calibrator of Sinusoidal Currents & Voltages, Power Factor Transduce

Calibration Block, Radiography LED Film Viewer, Ultrasonic Prob

ASME Sec. V Basic Calibration Block, Lead Lined Apro

We offer these Calibration Blocks for measuring specification of various metallic and non metallic tools under various parameters and are available in various specifications that meets International Quality Standards that are used for various kinds of engineering applications.

Calibration Blocks, Current Probe