Commercial Air Conditioner Dealers in Noida

Scroll chiller are easy to install and can work perfectly in extreme tropical weather conditions. These scroll chillers are designed, manufactured and tested as per approved international parameters. Installed equipments are operation friendly and are backed by competent engineering team to realize the advantage while being in operation.

Specifications Choice of screw compressor of hanbell (taiwan), bitzer (germany) & j&e hall (uk). All options are semi-hermetic in construction, thereby making it maintenance friendly. The screw compressor range offered is specifically developed for low temperature chillers applications and is offered along with adjustable volume ratio. Besides internally built oil separation system, check valves at suction and discharge port are provided as standard part of the oem equipment.  The screw compressor range offered is specifically designed by the respective oems for low temperature applications. High cop/eer  as an issue proficient gathering of the refrigerant. These water cooled chiller units are intended to meet the relevant necessities of ashrae/ansi 15 safety code. Since the condensers are liberally oversized, productive gathering of the refrigerant prompts lower ikw contrasted and other accessible brands. Shell & tube evaporator is constructed with copper containers of 19 swg that empowers them to withstand hard water with ph more noteworthy than 8. The copper tubes contain flamingo licensed star turbulator embeds that give turbulence to the refrigerant coursing through the copper tubes. As an issue of this turbulence these shell & tube evaporators have amazingly effective hotness exchange rate. The shell is produced from high-review steel. The evaporator is planned according to asme section viii div.1. Available in a choice of refrigerants R-22 (freon), R-407c and R-134a. Both R-407C and R-134A are environment neighborly and non-ozone draining refrigerants. Ultra efficient condensing using outer finned copper tubes for increasing heat transfer surface results in higher efficiencyin comparison to copper tubes without finning. The copper tubes are of 16 swg and are finned on the outer surface to accommodate up to 26 fins per inch. The copper tubes are mechanically expanded through a torque controlled machine on the tube sheets that are manufactured on imported vmc machine. Economizer for higher efficiency is provided as per refrigerant used and depending upon the liquid temperature range desired. Economiser is provided as standard part of supply in process chillers opted for evaporating temperature of 0 deg. C or lower. The economizer/sub-cooler enhances the overall capacity of the chiller by 10%, and reduces the power consumption, thereby increasing the overall coefficient of performance (cop). Available in a choice of refrigerants R-22 (freon), R-407C and R-134A. Both R-407C and R-134A are environment friendly and non-ozone depleting refrigerants. Additonal air cooled type oil cooler is added depending upon the refrigerant used and the chilled water/brine temperature desired. The oil cooler helps maintain the oil temperatures flowing through the compressor within safe limits. The oil cooler fan is automatically controlled depending upon the oil temperature. This feature enhances the screw compressor life. Liquid injection is a standard gimmick and is utilized to cool the compressor engine slowing down. When the release temperature surpasses the ordinary range, an electric solenoid curl infuses fluid refrigerant to keep the slowing down inside protected breaking points. This peculiarity upgrades the life of the screw compressor. Thermostatic expansion valve is given as an issue some piece of the water cooled screw chiller gear. Electronic extension valve can likewise be alternatively given. Control panel with ip-65 assurance is given as standard piece of the water cooled supplies. Microprocessor based controller is a standard piece of the water cooled screw chiller supplies. The controller permits various set focuses that can be arranged to specific set of values that may be considered inside the safe working extent. If there should be an occurrence of any rupture in any of the set point esteem the controller will excursion the chiller after the fed wellbeing postponement period has passed and show it on the lcd show. Additionally, the controller naturally conforms the limit in a stepped configuration making them perfect for variable burden applications.

JLS India Technology GMI-Germany Design Refrigerated Fluid Chiller System cools various fluids such as water, water/glycol or oil down to, or below, the ambient temperature. These provide Stable and reliable cooling for many common heat removal applications, including laser etching, AA furnaces, ICP, rotary evaporators, vacuum systems, reaction vessels, plasma etching and condenser cooling. Whether integrated into a machine or used as an auxiliary cooler, this system will tackle any cooling task and guarantees quality with utmost precision. . Features of Refrigerated Chiller Equipped with solenoid valve, pressure controller for safe, Silent and efficient         refrigeration. Liquid level indication sight window and pressure gauge help you observe the       circulating and cooling process going the way as expected Over temperature protection Air cooled condenser RS232 interface for PC-connection (Optional) USB ports (optional) CFC free refrigeration unit Real time data acquisition system (optional), TEMPERATURE RANGE Temperature range of our recirculatory chiller models is -10°C to 40°C.

Reynold Batching Plant Chillers, Batching Plant chiller are customized for concrete mixing and cooling applications with 4oC and 1oC chilled water temperatures, as per the process requirement. The chillers are designed to operate at highly dusty batching sites, within extreme weather conditions, working directly under sun and shower. The major components in the refrigeration circuits are chosen or designed as per the available site conditions and utilities.

We are manufacturers of plate heat exchangers used as sugar syrup chillers. the plate heat exchangers are made from ss clad frame with end connections of dairy sms union. Sugar syrup chiller capacities range from - 100 lph to 10000 lph types for sugar syrup chillers - 1. Single section sugar syrup chiller - 85 c to 37 c using cooling tower water 2. Single section sugar chiller - 37 to 25 c using ethylene glycol mixture 3. Double section sugar syrup chiller - first section cools the syrup from 85 to 37 c and second section from 37 c to 25 c

1) Cleanroom Architecture – Materials of construction and finishes are important in establishing cleanliness levels and minimizing the internal generation of contaminants from the surfaces. 2) Clean Room HVAC System – The integrity of the cleanroom environment is created by the pressure differential compared with adjacent areas through heating, ventilation and air-conditioning system. The HVAC system requirements include: Supplying airflow in sufficient volume and cleanliness to support the cleanliness rating of the room. Introducing air in a manner to prevent stagnant areas where particles could accumulate. Filtering the outside and re-circulated air across high efficiency particulate air (HEPA) filters. Conditioning the air to meet the cleanroom temperature and humidity requirements. Ensuring enough conditioned makeup air to maintain the specified positive pressurization. 3) Interaction Technology – Interaction technology includes two elements: (1) the movement of materials into the area and the movement of people and (2) maintenance and cleaning. Administrative instructions, procedures and actions are necessary to be made about the logistics, operation strategies, maintenance and cleaning. 4) Monitoring systems – Monitoring systems include a means of indicating that the cleanroom is functioning properly. The variables monitored are the pressure differential between the outside environment and the cleanroom, temperature, humidity and, in some cases, noise and vibrations. Control data should be recorded on a routine basis. HVAC SYSTEM DESIGN FOR CLEAN FACILITY HVAC systems in cleanrooms are substantially different from their counterparts in commercial buildings in terms of equipment design, system requirements, reliability, size and scale. A cleanroom differs from a normal comfort air conditioned space, in the following ways.   Increased Air Supply: Whereas comfort air conditioning would require about 2-10 air changes/hr, a typical cleanroom would typically require 20 – 60 air changes and could be as high as 600 for absolute cleanliness. The use of high efficiency filters: The use of high efficiency particulate air (HEPA) filters having filtration efficiency of 99.97% down to 0.3 microns is another distinguishing feature of cleanrooms. The HEPA filters for stringent cleanrooms are normally located at the terminal end and in most cases provide 100% ceiling coverage. Room pressurization: The cleanroom is positively pressurized (to 0.05 in-wc) with respect to the adjacent areas. This is done by supplying more air and extracting less air from the room than is supplied to it.   CHEMPHARM ENGINEERED SYSTEM INCLUDES ENERGY EFFICIENT KEY COMPONENT AS- Reciprocating/Screw/Scroll type Chiller Unit with VFD Controller. DX Unit/VRF unit Built-in PLC System for Low tonnage requirement. Hot Water Generator with Built-in PLC for Winter Heat/ Monsoon Reheat requirement. CHW/CDW pumps with VFD Drive to control the speed as per demand. Air Handler with centrifugal plug fan or DIDW Backward Curve fan has been select for controlled flow air based on the Flow & Static Pressure requirement of Varies application. Dehumidifier/ Humidifier System to Maintain the Inside RH/Tem all-round the Year. Heat recovery System to enhance the power saving. Thermal Filtration System with HEPA (H-13) or ULPA (H-14) filter where ever required as per Clean Room Classification. Factory built Square, Round or Oval Ducts having slip on or TDF type flanges based on the line / system  pressure and requirements – All ducts are built as per ASHRAE 2012 Duct construction Standard. Thermal Insulation are chosen based on Application & ambient condition but fibre free and as per ASTM standards – Standard specification / material are –Nitrile Rubber, XLPE , PU BASED , ROCK WOOL , MINERAL WOOL , GLASS etc 

Plate Chiller - Our Company manufactures high quality Plate Chiller/ Heat Exchanger, using premium grade material and components, under the supervision of highly qualified and experienced professionals of the Company, applying advanced cutting edge technology. Our offered Products meet the international norms and quality standards of the industry. The Machines are available in various sizes, designs and specifications of the industry, so as to meet diverse necessities of our valued customers.

We have marked a distinct and dynamic position in the market by providing a high quality array of Pre Air Filter that is widely used in those areas where low resistance & high dust holding capacity is required. At our well established manufacturing unit, our offered filter is quality proven, highly durable & requires negligible maintenance. The provided filter is precisely designed to eradicate the harmful particles, including mold spores, dust, dust mites, pet dander and other irritating allergens from the air. Besides this, our esteemed clients can avail this filter from us at industry leading prices. We are offering our products as per client requirement. Features: Sturdiness Robust design Seamless finish

Our vast range of highly efficient and compact Air Handling Units are used extensively in Heavy Application Industries, Malls, Hotels, Pharmaceuticals, and a variety of other applications. Frostech Air Handling Units are completely customised as per the given specificationsrequirements with premium quality designed as per latest technology to provide maximum efficiency at the most economical rates.

We make available, Auto Air Conditioning System, which is extensively used in various industries and widely acclaimed for its durability, cost-effectiveness and high performance.

We are manufacturing metallic air filters of viscous type of frames like Galvanized Iron wire mesh and Galvanized Iron Frame. Filters used in double skin air handling units and air washers are fabricated out of aluminium sheet frame and aluminium wire mesh. Pre filters are primary stage of filters used to arrest large dust particles of size less than 10 micron and rubber, dirt, sand etc from atmospheric air. We use MS, aluminum; S.S and G.I to make the body of Pre filter according to customer�s requirement. This filter are used in any air handling application. The Pre-Filter is in demand in both the national and international markets for its brilliant performance. We are among the reliable Pre Air Filters Manufacturers and Suppliers in India. Special units are designed for removing Odor with Carbon activated filter or Charcoal granules. We have units to maintain positive pressure in clean areas like Hospitals, Laboratories, Industries and even Residences. Since we have our in-house sheet Metal fabrication & design section we can deliver almost any unit as desired by our client. Airmake Cooling System Units are also used for pharma Industry for Ventilation purpose. Filters are available in two ranges. Rough filters & fine filters. Fine filters are for removal of particles down to 5 microns having an efficiency of 99.9% and rough filters for removal of particles down to 10-20 microns having an efficiency of 85% to 95%.Media & Support:- Superior quality non oven synthetic filter media is sandwiched between HDPE Needle punched media pleated for extended surface area. To eliminate the possibility of dirty air bypass the media pack is securely bonded to the periphery of the enclosure frame using epoxy hardene

The Double Skin Modular Air Handling Unit is designed based on modular paneling concept to fulfill the indoor air quality requirement. The air flow of DM AHU is within range of 330 to 20,000 lps (700 to 42379CFM) and up to a total static pressure of 1991 pa (8” W.G). For special design, the air flow can be reached25,000 lps (52974 CFM).The AHU is constructed of high strength extruded Aluminium to form rigid frame. Besides, it is with thermal barrier feature which using three leg-fiber plastic corner pieces, 25 or 50 mm Polyurethane (PU)insulation panel and all frames are insulated with 3.0 mm PE foam to minimize energy heat loss and prevent condensation occurring. The external clip method to hold the double skin PU insulation panel is easily accessible for maintenance while being air tight. The new thermal- break profile can perform better than the original profile in terms of providing better insulation and energy saving.There is selection software programme available: DM AHU, to optimize the best arrangement and performance for either chilled water system or DX system. Standard components can be selected and be placed according to customer requirement. Once the unit is defined, optional item and accessories are identified. The programme gives immediate feedback if there is no suitable choice for the units. The programme provides us with fan curves data, coil performance data, dimension, and shipment weight. McQuay can produce high quality, flexibility air handling unit which can provide excellent thermal efficiencies and to be airtight. Besides, air handling unit produced is with flexibility features to meet the indoor air quality, operating efficiency, sound level and installation requirement for today’s extensive   SALIENT FEATURES Application :Cooling, Heating, Dehumidification, Humidification in shopping malls, offices, restaurants, health care, multiplex, clean rooms and all type of industrial application Wide capacity range :2040 CMH to 59500 CMH Comfort to Industrial :pressure range from 250 Pa to 1500 Pa Product Range for all Application :   1. Horizontal Floor Mounted These units are suitable for large air quantity. The modular design allow flexible combination of component to suit specific application. hese AHU’s are ideal for large commercial / office / industrial / hospitality / healthcare application. 2. Unitary Vertical Floor Mounted These units are preferred when floor space is at a premium. Vertical units are units designed with filter coil & fan all arranged in a vertical frame. The advantage of these units are they occupy less floor space. Floor Plates where low ceiling height is a constraint multiple vertical units can be used to advantage. Where no AHU rooms are provided exposed units with supply air plenum can be used. 3. Ceiling Suspended Hide These units are suspended from ceiling slab above false ceiling and thus require no floor space & AHU rooms. These units are

We are engaged in manufacturing & supplying of Industrial Ducting. Used in industries and factories to control pollution, the Industrial Ducting are fabricated using superior grade material and latest technology. The complete range of Industrial Ducting is manufactured as per the set industrial parameters for quality. We have a team of strict quality controllers who test the Industrial Ducting to make sure that they are durable, sturdy and reliable. Features : Easy to handle and operateDurableHighly efficientRobust construction