Testing Equipment Dealers in Laxmi Nagar, Delhi

Digital DO Meter that we manufacture, export and supply is featured with temperature probe KCL, sodium sulphite crystals. Our Digital DO Meter has 3 ½ digit LED display along with overload indication. We make available Digital DO Meter with different accessories such as DO probe teflon, Do membranes and instruction manual. Moreover, we offer Digital DO Meter in bulk quantities and at nominal rates.

Cryptus employs a broad variety of tools and exploits to carry out penetration testing process. Each and every test is carried out by adept security testers and the results are manually verified before deliver to you the final result. The final result is you get complete and accurate compassionate of your security aspect and can immediately take remediation steps for closing any identified loop-holes.

Application AATCC Wrinkle Recovery Tester is used for determining a fabric’s ability to recover after wrinkling under a pre-determined load for a set period of time. A set of 5″x3″ dimensional plastic replicas is offered on request to grade the test samples 1 ~ 5. Optional order AATCC Wrinkle Recovery Tester Plastic Replicas (Set of 5) Weight - 5 kgDimensions Length : 150 mm Width : 150 mm Height : 330 mm Standards AATCC 128 ISO 9867 ENKA 3061 Why Do We Need to Test the Wrinkle Recovery of the Fabrics?In the process of wearing and keeping the fabric, because of the external forces, such as folding, shearing, compression, bending and washing, it is difficult to return to the original level state even after removing the external force. This phenomenon is called wrinkle. Wrinkle not only seriously affects the appearance of fabric, but also leads to severe wear along the crease or wrinkle direction, which accelerates the damage of fabric. Therefore, crease recovery is one of the important indexes to evaluate the fabric’s properties.Test PrincipleFabric wrinkle recovery instrument is used to test the recovery ability of fiber fabric samples under a certain load after bending for a certain time. Under the condition of standard atmospheric pressure, apply a predetermine pressure to the sample with the standard wrinkle device and keep the time set. The pressurized sample will produce uniform deformation through the whole structure of the instrument and the precise spiral column. Then the sample is compared with the standard sample and rated.Sample Preparation Cut three samples, 150mm * 280mm each. These should be cut with the long direction running in the warp or the wale direction of the fabric. At 21±1℃ and 65±2% humidity, each sample remained at least 8 hours in the state. Testing Procedure All tests were performed at the environment of 21±1℃ and 65±2% humidity. Raise the top flange of the recovery tester and fix it to the top of the tester with the lock pin. Wrap one long edge of a pre-conditioned test specimen around the top flange of the wrinkle tester, with the face of the specimen on the outside. Fasten the specimen in position using one of the strips of Velcro. Wrap the other end of the specimen on the flange, and then wrap the second piece of Velcro around the bottom of the specimen so that it forms a “closed tube” of fabric. Adjust the bottom edge of the specimen so that it lies smoothly without sagging between the top and bottom flanges. Withdraw the locking pin and lower the top flange gently with one hand until it comes to rest. Immediately place a total mass of 3500 grams (all three weights) on the top flange and record the time. After 20 minutes, remove the three weights and raise the top flange, carefully avoiding altering any of the induced wrinklings. Clamp the short edge side of the sample with a clip and hang the sample on a hanger, so that the length direction of the sample is perpendicular to the ground. After 24 hours in this conditioned atmosphere, take down the sample and rate it.

We are offering cell sensor radiation testing meter gauss meter measures mobile phone rf radiation, conjointly measures magnetic attraction fields generated by power lines, laptop monitors, tvs, appliances, home wiring, and alternative unknown sources.

We are offering digital level meter. Features the higest accuracy of the new products: 0.001 mmm new products adopt numerical circuit improved antijamming. standard interface output rs232 could communicate with computer diretcly. valued function of storage, read and delete the measured data, store data upto 999. adjust accurately and zero setup at any position keypress (absolute zero position and relative zero position) conserve and recover the factory settings are available. two optional measuring units: mmm and angle (second). be provided with the function of automatic temprature measuring. be provided with automatic temperature measuring. be provided with automatic electrical source voltage supervising and low voltage warning function. power supplied by aa battery. easy to operate by touch style induction panel.

CFL100 series flow meters are extremely versatile flow meters that can be used for a wide variety of applications. These meters offer extreme reliability and low cost for flow measurement and logging. CFL100 series flow Data loggers can be used for water. These meters can also be used for line sizes from 0.5” to 48”. Microprocessor based instrumentation ensures accurate readings for both rate of flow indication and total flow indication. A number of programmable features including In-line calibration are standard. All the parameters are saved in a non volatile EEPROM memory which doesn't needs any external battery. There is a advanced power fail feature by which even if there is any power failure the Total Flow reading is automatically saved to memory and resumes with the same value after Power On. Advanced models can offer relay outputs for signals exceeding rate of flow or total flow set points. Programmable pulse output models are also available in addition to the industry standard 4-20mA output. CFL100 Flow data logger has an RTC and external EEPROM to save flow rate and total flow and time of events. A maximum of 10000 records can be saved at time intervals specified by user in program menu. CFL100 has a direct printer interface which can print to a printer through RS232 port. This printing takes place at regular time intervals or user programmed time intervals. Advanced flow data logger can work in GSM Communication mode which transmits data through GSM modem either through SMS, GPRS, Data Call or by all the three programmable by user.

Piko-1 electronic peak flow & fev1 meter piko-1 measures peak flow and fev1, considered by many asthma specialists to be a more reliable indicator of an impending asthma attack. Recognized as the best over-the-counter and self care product at the us medical design excellence awards in 2003, piko-1 is more accurate in the measurement of peak flow than mechanical peak flow meters and is atseu scale compliant.