Test Rig Dealers

The Centrifugal Pump Test Rig is designed by us to allow students and researchers to study the performance of centrifugal pump. The set up consists of a centrifugal pump coupled with electrical motor, supply tank, measuring tank & pipe fittings for closed loop water circulation. Pressure and Vacuum gauges are connected on delivery and suction side of pump for the purpose of measurement. The flow rate of water is measured using measuring tank and stop watch provided. Objectives To determine overall efficiency and pump efficiency of the centrifugal pump.To plot Head vs. Discharge, Pump efficiency vs. Discharge. Salient Features Closed loop water circulationCompact & stand alone set upStainless Steel tanks and wetted partsSuperb Painted structureSimple to operate & maintain Utilities Required Electric supply : Provide 230 +/- 10 VAC, 50 Hz, single phase electric supply with proper earthing. (Neutral – Earth voltage less than 5 VAC.) 5A, three pin socket with switch for pump.Water supply : Tap water connection ½” BSPDistilled water : @ 80 liters (optional) » Technical Detail Product Centrifugal PumpTest Rig Pump Capacity 1 HP Speed 2800 RPM (max.), Head 12m(max.), Make Kirloskar Drive AC motor with step cone pulley arrangement for 3 prefixed speedDC motor with DC drive along with non-contact type digital RPM indicator Supply Tank Capacity 120 Ltrs. MOC SS Measuring Tank Capacity 75 Ltrs. MOC SS fitted with Piezometer Tube & scale Piping GI / PVC Stop Watch Electronic Control Panel With required electrical instrumentation

 Engine – ‘Bajaj Tempo automotive Diesel Engine . Four stroke four cylinder, water cooled, developing 35 BHP at 3000 rpm.provided with battery and self starter.2) Suitable capacity Hydraulic Dynamometer ORElectrical Dynamometer – suitable capacity alternator with loading arrangement.3)Measurements provided- Fuel intake measurement. Air intake measurement. Water circulated exhaust gas calorimeter. DigitalTemperature Indicator for Exhaust gas & water temperature. Tachometer. Gauges for jacket water temp. oil pressure & battery condition Arrangement to cut off the fuel injection to conduct morse test. The test rig enables to determine I.H.P. , B.H.P. , specific fuel consumption, Air fuel ratio Volumetric efficiency andheat balance sheet at different loads and speeds.A technical manual accompanies the unit.A technical manual is supplied alongwith the unitThe unit is provided with anticorrosion attractive powder coating.The unit with electrical dynamometer can be used as a diesel generator set for lab.

Automatic selection of the flow, pressure and speed on selection of the model Security (multiple level) to allow access, based on user levels Configuration of sensors and online calibration of sensors Specifications   Drive Motor Max Speed: 500-800 RPM Pump Supply Max Pressure: Max 200 Bar Pump Supply Oil Temperature: Ambient to 120deg C Shaft Load (Belt Load): Max 200kg Hot Chamber Temp. Control: Room Temp. to 100deg C (Optional) Drive Torque: Max 25Nm Pump Supply Max Flow: Max 25 LPM Pulley Ratio: 1:3.1 Test Configuration Possible: Diret Drive - Pulley Gear Mesh Drive

The company is a prominent Manufacturer and Supplier of Francis Turbine Test Rigs. This is a reaction turbine and this Test Rig shows the construction and working of Francis turbine. Rope brake dynamometer is used to measure the output of turbine. Pressure gauge and orifice meter are used to measure the input of turbine.   Specifications : This Francis Turbine Test Rig I00mm size to develop 2 HP at 1250 RPM with a flow of about 1400 Ipm at 15 meters supply head. Supply pump set lOOxlOOmm size, 1500 Ipm at 15 meter head suitable for supplying water to the above turbine. Monoblock Centrifugal Pump  -  (5 HP, 3 Phases, 440V) Pump Size  -  Suction size 80mm & Delivery size 80mm Pump Discharge  -  1500 LPM Delivery Head ; 15 meter RPM  -  3000 RPM   Sump Tank : MS Tank to store sufficient water for independent circulation through the unit experimentation and arrange Within the floor space of main unit. Capacity 650 Itr. Rope Bake Dynamometer is used to measure the output. Spring balance and dead weights are used to measure the load. Runner Diameter 220mm. Discharge Butter Fly valve used to control the flow rate of water. Spring Balance 6 Kg (Salter Make) Pressure Gauge of 4.2 kg/cm2 is used to measure the pressure head. Rigid MS frame work compactly fitted with all the above items as a self-sufficient package unit suitable for operation without any foundation. Switch and starter suitable for above motor pump set mounted on the control panel board. Experimental Capabilities : To determine the efficiency of Turbine To draw the characteristics curve of Turbine

We offer it in different specifications, so, that it can suit all your industry needs. These tools are highly demanded in various industries because of its unmatched quality and superb performance. Our team manufactures it with modern technology, so, that it can match international quality standards.

RANGE OF EXPERIMENTS :1. To study all components/Accessories used in Reciprocating Air Compressor.2. To study & determine Isothermal Work, Isentropic Work, Actual Work Volumetric Efficiency,     Isothermal Efficiency, Isentropic Efficiency & Free Air Delivery at different delivery pressure.3. To Plot Volumetric Efficiency/Isothermal Efficiency Isentropic Efficiency against Delivery    Pressure & comment on the nature of the plot.

The test rig is designed for the study of vapour Compression refrigeration cycle by way of demonstration and experimentation. Cooling circuit consists of a hermetic compressor; air cooled condenser, thermostatic expansion valve and evaporator (i.e. cooling coil). Measurements of various parameters Torn cooling cycle and heating cycle are provided and students can easily visualize and understand the basic principles of air conditioning.Experimentation : To Study the Vapour Compression refrigerator cycle. To Calculate Co-efficient of performance and draw P-H Diagram. Utilities Required: Electric supply 5A-220 V AC Water supply and drainage Floor area : 1.3 m x 1.2m

PELTON WHEEL TURBINE TEST RIG       The ‘J.P.T.I.’unit consist of a small pelton wheel connected to rope brake dynamometer. It is high head at minimum discharge turbine. Water is given from reservoir to the turbine . A centrifugal pump is provided to supply the water to turbine. Orificemeter & pressure gauges provided to measure flow rate, water jet is directed over the bucket by a nozzle Thus, we can determine B.H.P. & I.H.P. & various efficiencies.    

Based in Roorkey, Uttarakhand we have emerged as one of the focused manufacturers, exporters and suppliers of the Pressure Testing Rig. This system that we offer can be used to simulate aircraft fatigue induced by changes in altitude. The design and quality of all the products we offer are stringently checked and monitored at each stage to ensure that the final product meets is on par with industrial standards.   Details : To design a system to simulate few years of aircraft fatigue induced by changes in altitude. The system was required to pressurize and depressurize all voids within the aircraft and be accurate to within 0.1psi at all stages of the operation. A very high level of safety was required, to prevent any potential damage to an aircraft through over pressure. The input control signal would be sent via a PLC and the operation would be recorded.

The setup is designed to study the performance of reciprocating pump. Set up consists of a reciprocating pump coupled with electrical motor, supply tank, measuring tank & pipe fittings for closed loop water circulation. Pressure and Vacuum gauges are connected on delivery and suction side of pump for the purpose of measurement. The flow rate of water is measured using measuring tank and stop watch provided Experiments To determine overall efficiency and pump efficiency of the reciprocating pump. To plot Head vs. Discharge, Pump efficiency vs. Discharge Utilities Required Electric supply Provide 230 +/- 10 VAC, 50 Hz, single phase electric supply with proper earthing. (Neutral – Earth voltage less than 5 VAC.), 5A, three pin socket with switch for pump. Water supply Tap water connection ” BSP Distilled water @ 80 liters (optional)

0.5 H.P. pump to circulate water system through the piping. Sump tank : 1000 x 300 x 400 mm Measuring tank : 300 x 300 x500mm Rotameter of range 250 to 2500 LPH

Owing to our state-of-the-art warehouse, we efficiently entertain both automated inbound and outbound consignments with utmost proficiency. The products are sorted and segregated to make sure that the delivery commences systematically. We are a one-stop destination and the perfect place for purchasing excellence assured 4 Stroke Petrol Engine Test Rig.

While SKF has a rich history in the research and development of bearing technology, it also has deep roots in the field of lubrication technology. Through the development of a number of grease test rigs, we continue to deepen our understanding of lubrication theory and pass that knowledge on to our customers.