Test Rig Dealers

Francis Turbine is a reaction turbine, which was developed by an English born American Engineer Sir J. B. Francis. The water enters the turbine through the outer periphery of the runner in the radial direction and leaves the runner in axial direction and hence it is called a mixed flow turbine. As the water flows to the runner, a part of pressure energy goes on changing into kinetic energy. Thus the water through the runner is under pressure. The runner is completely enclosed in a air tight casing and the casing & runner is always full of water. The present set-up consists of a runner. The water is fed to the turbine by Means of Centrifugal Pump, radially to the runner. The runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is provided with a transparent acrylic sheet for observation of flow on to the runner. Load is applied to the turbine with the help of brake arrangement so that the efficiency of the turbine can be calculated. A draft tube is fitted on the outlet of the turbine. The set-up is complete with guide mechanism. Pressure and Vacuum gauges are fitted at the inlet and outlet of the turbine to measure the total supply head on the turbine Experiments To study the operation of a Francis Turbine To determine the Output Power of Francis Turbine To determine the Turbine Efficiency Utilities Required Water Supply and Drain Electricity 15 kW, 440V AC, Three Phase Floor Area 1.5 x 0.75 m

advanced technocracy inc. is manufacturer, exporter & supplier of water meter test rig. pump: 0.5 hp, 1ph, monoblock, make: kirloskar cricgequavalant sump tank: 1000 x 300 x 400 mm, ss304 or ms with frp coat collecting tank: 300 x 300 x 400 mm, ss304 or ms with frp coat flow meter: a turbine type flow meter 1" x 1" piezometer: a graduated glass tube ( graduation in cm) experimental capability: actual & theoretical discharge, co-efficient of discharge manual: self explanatory instruction manual with sample calculation

PELTON TURBINE TEST RIG is manufactured by Engineering Models and Equipments to demonstrating PELTON TURBINE , PELTON TURBINE TEST RIG can be availed from us in varied different specifications as per the requirements of the clients.

Spindles are tested as per DIN 8637 Standards for Temperature, Vibration at maximum speed. Condition monitoring will be undertaken on specific request.

The setup consists of single cylinder, four strokes, Diesel engine coupled to a rope brake dynamometer / electrical dynamometer or Eddy Current Dynamometer for variable loading. The setup has standalone type independent panel box consisting of air box, fuel tank, manometer, fuel measuring unit. Engine jacket cooling water inlet, outlet and exhaust gas temperature is also measured. Arrangement for cooling water flow rate measurement is also provided. The setup enables study of engine for brake power, brake thermal efficiency, volumetric efficiency, specific fuel consumption, air fuel ratio and heat balance.

We were the first air filtration company in Europe to invest in our own Eurovent & EN 779 test rigs. The test rigs have undergone rigorous 'round robin' tests to ensure consistency of filter evaluation with independent test laboratories.By having a number of our own test rigs we can test new filters as well as used filters from the field to build up our own database of how filters work and perform in real life. Standards have so far been concentrating on finding fast, economical methods to classify filters.

Low friction bearing Geared AC servomotor Analog outputs for torque and angle Friction compensation (during calibration) Specifications   Rotation Actuator: 20Nm Torque Sensor: Inline Speed: 0.1 RPM to 10 RPM

Triotech have developed tractor transmission test rig for 70 HP capacity. Also designed & manufactured drive line modules required for these test rigs.

We are offering centrifugal blower test rig the apparatus consists of a spiral casing, which houses an impeller. Impeller is driven by a variable speed d.c. Motor. Three, interchangeable impellers, viz. Radial forward and backward curved vanes are provided with the unit. Digital indicators are provided for speed of impeller. A venture provided measures the discharge. Thus students can evaluate the performance of different impellers at various speeds. specifications: 1. blower - spiral casing with three interchangeable impellers viz. Forward, backward and radial vanes. 2. drive motor-1 hp dc motor, 3000 rpm with dimmer control to vary the speed from 300 to 3000 rpm. 3. digital speed indicator for speed measurement. 4. ventura with water manometer to measure air flow. 5. water manometer to measure discharge pressure. 6. discharge pipe with flow control valve. a technical manual accompanies the unit. Services required: 1. floor space of about 2m x 1.5m x 1.5m height. 2. 230 v. 5a., 50 hz, ac supply.

The Heat Pump Test Rig is a self –contained unit. All the components of Heat Pump Test Rig are mounted such that its operation and working can be easily understood. The required controls for temperature, pressure, and overload are provided in our Heat Pump Test Rig. The Heat Pump Test Rig uses a hermetically sealed compressor, heat rejection chamber, heat absorption chamber, and apparatus to measure the heat gain and heat loss. List of Experiments To study various components and controls used in heat pumpTo evaluate gross heat rejection of the heat pumpTo calculate actual & theoretical C.O.P. of the systemTo plot system performance on Ph chart Rating Conditions Ambient temperature= 350 CAtmospheric pressure = 1.01 barSuction pressure = 35 psigDischarge pressure= 180 psigEvaporation temperature = 7.70 CDischarge temperature = 550 C.

The journal bearing test rig for investigating the distribution of pressure in slide bearings the principal of hydrodynamic lubrication. The distribution of pressure & the carrying capacity can be determined on a sliding bearing model at different bearing loads & speeds. Learning objectives/experiments Relocation of the shaft journals in relation to speed Pressure distribution in the bearing with constant load and at various speeds Critical speed in relation to load Critical speed & viscosity in relation to oil temperature Category: Test Rig

To Study The Shock Absorber  To plot the transmissibility curve of shock absorber   Product Code : SAMS AUTO - 002

Here simple demonstration setup is provided to experiment with characteristics of Thermocouple. Here using this setup one can calibrate different types of thermocouples. SPECIFICATIONS 1. Water Bath with heating arrangement. 2. Thermocouple with necessary signal conditioning circuit. 3. Thermometer. 4. Measurement of oC and Mili Volt on Digital Display 5. Digital Indicator: -    • Least Count: - 1 deg    • Digit: - 3 1/2 6. Powder coated enclosure.