Test Rig Dealers

Type of Test: Non destructive  Purpose: Radial Load Vs Deflection Prime Mover: Compressed Air  Brief Specifications: Maximum Load capacity- 1500kg Digital display of load and deflection under specific load  Options: Data Acquisition System and PC software  

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Closed Circuit Francis Turbine Test Rig 5 HP Capacity A. Francis Turbine Type : Inward Flow Reaction Turbine Capacity : 5 HP Rated Speed : 1250 RPM Discharge Capacity : 1800 LitersMinute Supply Head : 25 Meters Guide Vanes : Gun Metal Vanes (Aerofoil Blade Shaped) B. Loading Rope Brake Material :Cast Iron Drum Size :300 mm diameter C. Supply Pump Set Size : 4 X 4 Discharge :: 1800 LitersMinute Total Head : 30 Meters Motor Capacity : 15 HP Make : CRISugnaCoimbatore Starter for Motor : S t a r D e l t a - TCCrompton Make D. Flow Measurement Material : C.I Body Manometer Fluid : Mercury E. Pressure Measurement Pressure & Vacuum gauge F. RPM Indicator G. Sump Tank : Digital Material of Construction M.S. FRP : MS Powder Coating

We have manufactured and installed Booster Rocket Engine Test Rigs having rocket motor diameter of up to 2 meters and thrust range of up to 25 tonnes. These can be manufactured and installed for Axial thrust measurement Six component thrust measurement.

RANGE OF EXPERIMENTS :1. To study all components/Accessories used in Reciprocating Air Compressor.2. To study & determine Isothermal Work, Isentropic Work, Actual Work Volumetric Efficiency,     Isothermal Efficiency, Isentropic Efficiency & Free Air Delivery at different delivery pressure.3. To Plot Volumetric Efficiency/Isothermal Efficiency/Isentropic Efficiency against Delivery    Pressure & comment on the nature of the plot.4. To Observe & comment the temperatures of air at different stages.

The photo is design and develop for the Pulley bearing test Rig for endurance test of the automotive Pulley bearings.  This pulley bearing test rigs are using for life cycle test of the verios types of Pulley bearings and micro groove belt life cycle testing.JKS Ttech also design and develops extreme condition testing of the Pulley bearings and various types of bearings and belts.We also offering mud spray, salt spray, and oil spray during the endurance testing to validate the product in real conditions.   

we are offering steam jet refrigeration test rig. the steam jet refrigeration test rig (naesjr), offered by us, consists of steam ejector, an evaporator, a condenser mounted on a board as shown in the picture. necessary valves at the inlet & exit of the ejector, and between ejector and evaporator are provided in this steam jet refrigeration test rig (naesjr) for the flow variation and maintaining the pressure differential. an insulated water sump is used in steam jet refrigeration test rig (naesjr) as a source of circulating water. a small submersible pump is fitted in the sump for the circulation water through the system. our steam jet refrigeration test rig (naesjr) has a digital temperature indicator with a provision of six numbers of channels to indicate temperatures at various points. why our steam jet refrigeration test rig (naesjr)? accurate in testing efficiently maintains the pressure differentialworking can be easily understoodeco-friendlyindicates temperature at all levels easy to use

Automatic selection of the flow, pressure and speed on selection of the model Security (multiple level) to allow access, based on user levels Configuration of sensors and online calibration of sensors Drive Motor Max Speed: 500-800 RPM Pump Supply Max Pressure: Max 200 Bar Pump Supply Oil Temperature: Ambient to 120deg C Shaft Load (Belt Load): Max 200kg Hot Chamber Temp. Control: Room Temp. to 100deg C (Optional) Drive Torque: Max 25Nm Pump Supply Max Flow: Max 25 LPM Pulley Ratio: 1:3.1 Test Configuration Possible: Diret Drive - Pulley Gear Mesh Drive

The setup is designed to study the Hydraulic Ram. Hydraulic Ram is used for pump little quantity of water to high head from a large quantity of water available at low head. It works on a principle of water hammer stating that “when flowing water is suddenly stopped in a long pipe a pressure wave travels along the pipe creating an effect of water hammer”. Set up consists of a pipe section fitted with a pulse valve and non-return valve, a supply reservoir on a stand which is connected to an overhead tank, an air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic. The flow rate of useful and waste water is measured using measuring tank and stop watch provided. Pressure and Vacuum gauges are connected on delivery and suction side for the purpose of measurement Experiments To find out discharge of useful water and waste water. To find out the efficiency of the Hydraulic ram Utilities Required Electric supply Provide 230 +/- 10 VAC, 50 Hz, single phase electric supply with proper earthing. (Neutral – Earth voltage less than 5 VAC.), 5A, three pin socket with switch for pump. Water supply Tap water connection” BSP Distilled water @ 250 liters (optiona)

The Ice Plant Test rig works on simple vapour compression refrigeration cycle and uses R134a or R 404 A as a refrigerant. These are environment friendly. The system is fabricated such that students can observe and study ice formation process. It is also useful to understand working of vapour compression system, its performance and controls used. The arrangement of parts such that, all the parts are visible and working can be easily understood. Specifications subject to change without any notification. List Of Experiments: TO EVALUATE CAPACITY OF THE ICE PLANT. TO CALCULATE C.O.P. OF THE SYSTEM. TO PLOT SYSTEM PERFORMANCE ON P-H CHART Rating conditions * : Ambient temperature= 35o C, atmospheric pressure = 1.01 bar, suction pressure= 5 psig, discharge pressure= 180 psig, evaporation temperature=- 14o C, discharge temperature=55o C.  

Leak testing Machine is suitable for leak testing of Automobile part. This is "Decay" type testing machine to suit comprehensive range of tests. This machine has all advanced features may be required for precision detection of leakage. Specifications Highly reliable & dependable Microcontroller /PLC based Digital controller Smart pneumatic circuits Accurate measurement User friendly operation Protection through user password Multi channel test facility Process status indication