Power Cables Dealers in Mumbai

Armouring steel wires are galvanized steel wires in round and strips. These wires are commonly used for the protection (prevention of accidental damage), the provision of additional strength, and for earthing of all grades of electric cables.

LT Aerial Bunched cables, also known as LT AB Cables, are distinct from bare conductor overhead distribution. They are good for distribution of electricity to residential, commercial and industrial units. These cables have overcome limitations of PVC insulated cables such as thermal degradation, poor moisture resistance and thermoplastic nature. LT AB cables have higher current rating, higher short circuit rating approximately 1.2 times that of PVC. LT AB Cables have lower cost of laying because of comparatively smaller diameter of cable and higher weight. Installation charges are also low as diameter of the cable is comparatively lesser with smaller bending radius, requiring less space. For longer cable length voltage drop, one size lower cables can be used as compared to PVC insulated cable.   LT AB CABLE - COMMON SIZES 2C x 10 Sq mm 2C x 16 Sq mm 2C x 25 Sq mm (3C x 50 Sq mm) + (1C x 55 Sq mm) + (1C x 25 Sq mm) (3C x 70 Sq mm) + (1C x 55 Sq mm) + (1C x 25 Sq mm) (3C x 95 Sq mm) + (1C x 55 Sq mm) + (1C x 25 Sq mm) 4 x 10 Sq mm 4 x 16 Sq mm 4 x 25 Sq mm LT AB CABLE - FEATURES AB cables are highly reliable and insulation has been developed to withstand extreme cold and intense sunlight. Disturbance and faults occur five to ten times more often in open wires lines than in AB cable lines. There is no risk in touching the live cable and the insulation reduces the number of short circuits and over voltage faults in overhead cables during thunderstorms. Few hardware accessories are needed which are different for different size of cables. Streets can be lit only at little extra conductor for lighting. The cable can be supplied with one or two insulated conductors for street lighting. Convenient Usage In electricity theft prone areas. As replacement of bare lines in rural area & narrow street with limited space. As replacement of bare lines where reliabilities of support is of prime importance. In hilly terrain here cost of erection of overhead lines or under ground cable becomes very high. As reinforcement of existing system with increase in voltage/current carrying capacity. For temporary supplies. Advantages In comparison with bare overhead distribution line AB Cable has very high reliability in maintaining power services because power and neutral conductors are insulated with the best dielectric, resulting in the following advantages: Less fault rate on account of good protection against line and ground faults by high winding falling trees or birds specially in hilly areas and forests. High insulation resistance to earth in all seasons. Neglible lekage currents and low losses. Multiplexer circuits of power and telephone cables could be in the same set of poles. Better adaptability to laid besides with existing overhead bare conductor system without any interference. High capacitance and low inductance leading to low impedance of lines. Lower voltage drop, higher current carrying capacities vis-à-vis better voltage regulations. Longer spans and longer distance lines are possible with better system stability. AB cables are much safer than bare conductors. It can be laid in dense vegetation and forest areas. Additional connections can be easily and quickly made with hot line connectors. Overall lines cost is reduced. Maintenance is very convenient. Very difficult to tap the AB cables, thus reducing theft which leads to lower distribution losess. Since, the tension from the current carrying conductor is totally removed by introduction of messenger wire, the operating temperature of the conductor is 90 c as against 75 c thereby allowing AB cable to carry current equivalent to that of bare conductor of the same size.

LT Aerial Bunched cables, also known as LT AB Cables, are distinct from bare conductor overhead distribution. They are good for distribution of electricity to residential, commercial and industrial units. These cables have overcome limitations of PVC insulated cables such as thermal degradation, poor moisture resistance and thermoplastic nature. LT AB cables have higher current rating, higher short circuit rating approximately 1.2 times that of PVC. LT AB Cables have lower cost of laying because of comparatively smaller diameter of cable and higher weight. Installation charges are also low as diameter of the cable is comparatively lesser with smaller bending radius, requiring less space. For longer cable length voltage drop, one size lower cables can be used as compared to PVC insulated cable. LT AB CABLE - FEATURES AB cables are highly reliable and insulation has been developed to withstand extreme cold and intense sunlight. Disturbance and faults occur five to ten times more often in open wires lines than in AB cable lines. There is no risk in touching the live cable and the insulation reduces the number of short circuits and over voltage faults in overhead cables during thunderstorms. Few hardware accessories are needed which are different for different size of cables. Streets can be lit only at little extra conductor for lighting. The cable can be supplied with one or two insulated conductors for street lighting. Convenient Usage In electricity theft prone areas. As replacement of bare lines in rural area & narrow street with limited space. As replacement of bare lines where reliabilities of support is of prime importance. In hilly terrain here cost of erection of overhead lines or under ground cable becomes very high. As reinforcement of existing system with increase in voltage/current carrying capacity. For temporary supplies.Advantages In comparison with bare overhead distribution line AB Cable has very high reliability in maintaining power services because power and neutral conductors are insulated with the best dielectric, resulting in the following advantages: Less fault rate on account of good protection against line and ground faults by high winding falling trees or birds specially in hilly areas and forests. High insulation resistance to earth in all seasons. Neglible lekage currents and low losses. Multiplexer circuits of power and telephone cables could be in the same set of poles. Better adaptability to laid besides with existing overhead bare conductor system without any interference. High capacitance and low inductance leading to low impedance of lines. Lower voltage drop, higher current carrying capacities vis-à-vis better voltage regulations. Longer spans and longer distance lines are possible with better system stability. AB cables are much safer than bare conductors. It can be laid in dense vegetation and forest areas. Additional connections can be easily and quickly made with hot line connectors. Overall lines cost is reduced. Maintenance is very convenient. Very difficult to tap the AB cables, thus reducing theft which leads to lower distribution losess. Since, the tension from the current carrying conductor is totally removed by introduction of messenger wire, the operating temperature of the conductor is 90 c as against 75 c thereby allowing AB cable to carry current equivalent to that of bare conductor of the same size.

We manufacture and distribute an extensive range of copper & aluminum conductor unarmoured cable. these are highly used in ac single phase or three phase (earthed or unearthed) systems for rated voltages up-to and including 1100 volts or a dc systems for rated voltages up-to and including 1500 volts to earth.

Aerial bundled cables (also aerial bundled conductors or simply ABC) are overhead power lines using several insulated phase conductors bundled tightly together, usually with a bare neutral conductor. This contrasts with the traditional practice of using uninsulated conductors separated by air gaps. This variation of overhead power lines utilizes the same principles as bundled conductors, except that they are closer together to the point of touching but each conductor is surrounded by an insulating layer (except for the neutral line). The main objections to the traditional design are that the multiple conductors are considered unappealing, and external forces (such as high winds) can cause them to touch and short circuit. The resultant sparks have been a cause of bushfires in drier climates. In the UK where some supplies to rural property are converted to PME/MEN from TT Earthing system concerns have been expressed that the lower conductor alone may be broken, (by high vehicle or falling tree for example) but with the upper phase conductors intact. This is a potentially dangerous fault condition. With ABC, a simultaneous disconnection of all conductors is more likely. In moister climates, tree growth is a significant problem for overhead power lines. Aerial bundled cables will not arc over if touched by tree branches. Although persistent rubbing is still a problem, tree-trimming costs can be reduced. Areas with large trees and branches falling on lines are a problem for aerial bundled cables as the line degrades over time. Due to the very large strain forces cracking and breaking insulation can lead to short circuit failures which can then lead to ground fires due to dripping of molten insulation. Low voltage ABC has already been developed in several countries across the globe and promises to be cheaper, safer, more reliable, require less tree clearing and pruning, be more aesthetic, be less labor intensive, require less maintenance and eliminate bushfires being initiated by conductor clashing.

By utilizing skills of our dexterous workforce, we are offering a comprehensive assortment of HT Elastomeric Cables. We manufacture these cables by employing optimum quality material along with sophisticated technology in adherence to the defined industrial standards. Our cables have wide application in all kind of industry and are used at home too for wiring.

Making use of the finest quality material, we manufacture a high performing collection of Screen Flexible Unarmoured Cables that are provided in both copper braided and aluminium mylar with 0.5 sq mm drain wire type. These cables find wide application in secure communication, high concentration of electrical equipments and industrial factory floor. Customized in accordance to the requirements of our clients, these cables hold the following benefits: Improved Attenuation Improved Power Sum Crosstalk Less noise interference

JPDP DESKTOP POWER CABLE PREMIUM 14X36 • Standard power cable used in PCs ,monitors & Printer • Also known as a kettle lead,Supplied with 5A fuse • Fully moulded mains lead • Comes with Black Fuse Cover. • Wire: copper wire to reduce interference magnetically shield for high speed Ethernet noise proof • 14x36 gauge

Armored cable with layers of Mica Glass Tape, EPR XLPE Silicon FR-XI,PF, insulated, cores laid up, extruded FRLS LSOH inner sheathed, Unarmoured GlArmoured, extruded FRLS LSOH Outer sheathed Fire Survival Cables generally conforming to IEC 60331,

Yasmee make Aluminium Welding Cable made up of single core double insulated flexible quality Aluminium Conductor in a coil of 100m ranges from

We manufacture copper flexible and armoured cables. Also a Huge stock is maintained of such cables. Insulations of HR, FR, FRLS, XLPE can be done on client's request.

Sheathed Multicore Cables with flexible conductors are manufactured with most stringent quality control to ensure total safety, prevention of shock hazards, less possibility of fires and complete assurance for a perfect system.

Our well-structured warehouse is properly maintained and installed with diverse amenities required for the safe storage of the products. Moreover, we keep on updating the unit for enhanced safety. We have an extensive supply-chain system that empowers us to ensure a distribution of consignments is done within the postulated time. Features : High tensile strength Corrosion resistant Perfect finish

Zenium 1100 Volts power cables manufactured using high grade XLPE insulation which provides better operating temperature than any other compound, with electrolyte grade stranded copper/aluminium laid together, extruded using protected PVC inner sheath, Special zinc coated galvanized iron wire/strip armour providing protection against any external environmental hazards. This assembly is overall sheathed with high grade PVC with FRLS and ZHFR compounds that are designed and tested. These cables meet national and international standards like IS:7098 part-1:1988 and IEC 60502. These cables are suitable for use in fixed installation.

  Selection of Power Cables     Power cables are generally selected considering the application. However followingfactors are important for selection of suitable cable construction required to transport electrical energy from one end to other.     Maximum operating voltage     Insulation level     Frequency     Load to be carried     Possible overloading duration & magnitude     Route length and voltage drop     Mode of installation considering installation environment such as ambient & ground temperature.     Flame retardant properties     Plant safety requirements

XLPE CABLES Most commonly used insulation for all voltages from low voltage to Extra High Voltage. All the above cables are available with standard PVC outer sheath & special outer sheath with FRLS, FR & PE.

Transmission Line SBU is the primary and largest business vertical of the Company. It manufactures entire range of Transmission Line Towers used in power Transmission & Distribution (T&D), having manufacturing facility at Boisar, Tarapur, Dist Thane with a fabrication and galvanizing capacity of 108000 MT per annum thereby making Karamtara one of the largest tower manufacturing facility in India under one roof.

Xlpe cables, High Voltage XLPE cables up to 66 KV on a high precision CCV line from ScholzSupermac (Dry Cure Dry Cool system) and Royale Systems, We also offer Low Voltage and Medium Voltage XLPE cables for continuous operation of 105°C instead of normal 90°C offered by competition. This allows more Power transfer for same conductor size.

TEGH CABLES PVT. LTD has established its name in India and abroad for its quality and commitment to customer satisfaction. To meet ever increasing demand of TEGH CABLES PVT. LTD cables, the company has put up a new state-of-the-art manufacturing unit at Mumbai (Maharashtra) where the XLPE insulated heavy duty cables are manufactured using latest technology. Click Here for Specifications