Dryer / Drying Machine Dealers in Ahmedabad

Agro Waste Dryer or Saw Dust Dryer Bio Mass Dryer for pallet manufacturing process. After drying from our supplied biomass dryer moisture level below 20%. We are using best technology in which biomass dry with using optimize energy. We are in business of manufacturing of Agro Waste Dryer or Saw Dust Dryer Bio Mass Dryer. If you have require Agro Waste Dryer or Saw Dust Dryer Bio Mass Dryer for pellet manufacturing process for that please specify following things. The capacity of Agro Waste Dryer or Saw Dust Dryer Bio Mass Dryer dryer in Ton per Hour.

Model ID: DP Series For almost two decades now, Trident Pneumatics, has devoted its expertise to innovating critical compressed air solutions. 

The feed product is evenly distributed by the rotor and its wipers over the heating surface, forming a thin liquid film of uniform thickness. Highly turbulent swirls are produced at the tip of the rotor blades and wipers with intensive mixing and agitation of the product, as it comes into contact with the heating surface. This assures excellent heat transfer combined with constant renewal of the product film and provides an even heating and short residence time of the product through the heated zone.

Moisture, either liquid or vapor, is present in compressed air as it exits the compressor system. If this moisture is not properly removed, your compressed air system can lose efficiency and require dramatically increased maintenance, which can result in costly downtime.The majority of pneumatic instruments and processes can not tolerate hot compressed air, compressors are normally supplied with after-coolers and moisture separators. After-coolers are heat exchangers that utilize either water or ambient air to cool the compressed air. As the water and lubricant vapors within the compressed air cool, a significant amount condenses into liquid. An after-cooler discharging compressed air at 100F passes 67 gallons of water per 1,000 scfm per 24 hours.To avoid these problems, compressed air systems have purification devices available to remove the water vapor and other contaminants. The proper selection of these devices is critical as pneumatic applications and compressed air systems become increasingly sophisticated.

Available in different sizes start from 150 mm dia to 600 dia in different length and different construction of material like, M.S / S.S etc. These could be used either horizontally or up to an inclination of 45 degree or so.  

DESCRIPTION :FBD 30,FBD 60,FBD 120,FBD 200,FBD 250. Capacity Of Dryer In kglt : (At 0.6 Bulk Density)25 -40,50 - 70,120 -150,200 - 220. Working Capacity of :( Product Container In Lit):50,100,200,330.

The fertilizer drying drum machine is used to dry compound fertilizers with required humidity and size of the particles. It not only dries the compound fertilizers but also dries other granular material. The moisture content will be reduced from 5% to 30% of the compound fertilizers whereas while drying bio-organic fertilizer, the moisture levels will be reduced from 40% to 10%. Features High utilization rate of heat energy due to efficient design. Strong adaptability of fertilizers and other materials. Low energy consumption due to small resistance for hot air. Huge capacity of the drying drum. Benefits Reliable operation with high yielding. Ideal for mass fertilizers production. Simple and easy drying process. Low maintenance and repair cost. Lengthy service life. Automation operation with better drying effect.

We Ultra Febtech - An ISO 9001:2008 Certified Company Engaged in Manufacturing of Pneumatic Flash Dryer for material handling .Pneumatic Flash Dryer will be effectively used for drying the wet material and convey it. The drying takes place in wide and high vertical tube. The material is sucked into the tube with a negative suction. The hot air is also carried with the material. Cyclones will be attached for the air and material separation. Necessary air lock will be provided with the system.

The highly effective-circulating system is provided. Uniform design, controlled temperature, sturdy construction & large working space. All contact parts are SS 316/316L. and non-contact parts are S.S. 304.  Process timer with the digital control panel. Flameproof design and motor with FLP control Panel(optional). Digital temperature controller. Aluminum/polypropylene/Frp/M.S. galvanized trays available on demand. Steam radiator/Steam accessories available on demand in compliance with cGMP.  

Our Tray Dryer Is Designed For Uniform Circulation Of Hot Air In The Drying Chamber. Electrical / Steam / Oil Heating Mode SALIENT FEATURES:- Inside Surface Is Painted With Heat Resistant Aluminum Paint And Out Side With Synthetic Enamel.  cGMP Models With SS 316 Construction, Single Page Design, Coving Coroners, Fully Washable Type Models Available.  Inside Of The Dryer. If Consists Of Starters, Contactors, Safety Relays, Ckt Breakers, Indicating Lamps, Push Buttons, Timers, Controllers Etc. Construction External Tray Dryer: 2mm Thick Internal: 2mm Thick Moc: CGMPSurface Finish External Tray Dryer: Buffed To 150 Grit Matt Finish Internal Tray Dryer: Buffed To 220 Grit Mirror Finish. Inlet & Outlet:- All Tray Dryers Have A 5 Micron Pre Filter At The Inlet And A Manually Infinite Adjustable Damper At The Outlet. Door:- Doors At Provided At The Front And / Or Rear Side Of The Dryer. Door Lips Are Lined With Silicon Rubber Gasket To Prevent Any Leakages. Suitable Locking Is Provided For The Doors Of Tray Dryer. Air Circulation:- Air Circulation Is Done By Specially Designed Recirculation Blowers Inside The Tray Dryer. The Blower Capacity, Static & Design Depends On The Size And Model Of Dryer. Heating: Dryers Are Normally Supplied With Either Steam/ Electric/ Thermic Fluid / Hot Water Heating System. Suitable Heating Coils / Caloriefiers Are Provided In The Tray Dryers. Temperature Control Temp Control System Is Done By Electronic Digital Temp Controller Fitted In The Control Panel. The Temp Control In The Dryer Is Fully Automatic. Trays:- Trays Are Available In S.S. 304/ 316 Q. All Trays Are Fully Die Pressed And With Coved Corners. Trays Are Buffed To Mirror Finish. Trays Are Also Available In Aluminum / Polypropylene / Frp/ M.S. Galvanized As Per Clients Requirements. Trolley:- Trolley Is Provided In The Tray Dryers To Accommodate Trays In It. Trolley Trucks Are Used To Load And Unload The Trays Into The Dryer. Control Panel:- Automatic Control Panel Is Fitted On The Side Of The Dryer. If Consists Of Starters, Contactors, Safety Relays, Ckt Breakers, Indicating Lamps, Push Buttons , Timers, Controllers Etc.

Electrical heating Scope: The Air inside the Tray Dryer is heated by "U" tube MS/S.S. air heaters each of 1 KW. TheHeaters are fitted on the sides of the dryer to facilitate uniform heating. Maximum temperature Attained inside the dryer is 100' C and will be indicated and controlled by a Digital Temperature indicator cum controller over full range of heating load. Trays Description: Trays will be manufactured from 1.6 mm Alluminium /MS/SS sheets as per client’s application. The dimensions of Trays are 16" x 32" x 1.25". Trays have rounded corners with' mirror finish from inside and outside. Quality is available on demand Racks And Trolleys Racks are provided for trays inside the Dryer. They are of fixed type for 12 & 24 Trays Models. For 48,96 and 192 Trays Models racks are provided with wheels to slide them in and out of the Dryer.  An additional S.S, trolley for Racks for outside movement can be provided on request Advantages:   Large production capacity, Continuous operation; Simple structure, Easy to operate; less failure, Low maintenance costs; A wide range of application, Fluid resistance is small, You can use it to dry granule-like material, for those adhesion material It is also very beneficial; Operating flexibility, production flow allows the product to have a greater fluctuation range, will not affect the quality of the product Cleaning easy Simple system Flexibility in fuels used.

We are a trustworthy Supplier and Exporter of Cashew Nut Dryer in Gujarat, India. Our high-quality cashew nut dryer (30 kg to above 500 kg) has efficient ovens that are multipurpose, as they can be used baking cashews, raisins, mango, jack fruits, sweets cakes, and bakery items. In order to bake the cashews, we follow the procedure in which a hot current is circulated in the oven by using various blowers and hence, all cashew nuts are baked evenly. The tray and other important parts are powder coated. The capacity of the dryer is around 30 kg.

Condition methane generated through anaerobic digestion for optimal use in micro turbines or combustion engines, and water vapor to protect gas compressors and to remove water vapor from low-Biogas to meet contract specifications.

It employs a Vapor-Compression Refrigeration Cycle commonly found in household Refrigerators and Air Conditioners to bring down the sensible temperature of Compressed Air. When we cool the Compressed Air down to around 2°C, Moisture in the Compressed Air turns into Bulk Liquid which is further separated in the stream Technical Specifications: Maximum Pressure Capacity: 16 bar Standard Flow Capacities: 10, 15, 20, 30, 45, 50, 60, 100, 125, 200, 250, 300 CFM and so on Pressure Dew Point (PDP): 3°C